Version vom 3. Dezember 2005, 15:54 Uhr

Dieser Artikel befindet sich möglichrweise im Aufbau. Siehe Diskussion:Codesammlung_avr-gcc

IR-Empfang

RC5 Decoder für AVR Mega

Beschreibung

Resourcen

Interface

#define RC5_INT0 0
#define RC5_INT1 1

#define RC5_ALL 0xff

typedef struct
{
	uint8_t code;
	uint8_t addr;
	volatile char flip;
} rc5_t;

extern rc5_t rc5;
extern void rc5_init (uint8_t addr);

void rc5_init (uint8_t addr)

Initialisiert die Hardware für RC5-Empfang. Akzeptiert wird Code, der an Adresse addr geschickt wird. Falls addr = RC5_ALL bzw Bit 7 von addr gesetzt ist, werden alle Adressen akzeptiert.

extern rc5_t rc5

In rc5 wird der empangene RC5-Code geliefert.

rc5.code

der empfangene RC5-Code, falls rc5.flip != -1

rc5.addr

die Adresse, an die gesendet wurde, falls rc5.flip != -1

rc5.flip

das Flip-Bit

rc5.flip = 0

Flip-Bit ist 0, RC5-Empfang inaktiv

rc5.flip = 1

Flip-Bit ist 1, RC5-Empfang inaktiv

rc5.flip = -1

RC5-Empfang aktiv, wartet auf nächste Übertragung

Code

rc5.c

#include <avr/io.h>
#include <avr/signal.h>

#include "rc5.h"

#ifndef RC5_INT
#define RC5_INT      RC5_INT0
#endif  // RC5_INT

#ifndef RC5_PRESCALE
#define RC5_PRESCALE 1024
#endif  // RC5_PRESCALE

//////////////////////////////////////////////////////////////////////////////

rc5_t rc5;

//////////////////////////////////////////////////////////////////////////////

// µs for a whole bit of RC5 (first & second part)
#define RC5_BIT_US   (64*27)

#define RC5_TICKS \
	((uint8_t) ((uint32_t) (F_CPU / 1000 * RC5_BIT_US / 1000 / RC5_PRESCALE)))
	
#define RC5_DELTA \
	(RC5_TICKS / 6)
	
typedef union 
{
	uint16_t w;
	uint8_t b[2];
	
	struct
	{
		unsigned code:6;
		unsigned addr:5;
		unsigned flip:1;
		unsigned agc:4;
	} __attribute__ ((packed));
	
} code_t;

static code_t code;
static uint8_t rc5_addr;

// Number of Bits received so far
// Number of Interrupts occured so far;
#ifndef RC5_DEBUG
static uint8_t nbits;
static uint8_t nint;
#else
uint8_t nbits;
uint8_t nint;
uint16_t * const prc5_code = &code.w;
#endif // !RC5_DEBUG

//////////////////////////////////////////////////////////////////////////////
	
void 
rc5_init (uint8_t addr)
{
	nint = 0;
	nbits = 0;
	rc5.flip = -1;
	
	rc5_addr = addr;
	
#if (RC5_PRESCALE==1024)
	TCCR0 = (1 << CS02) | (1 << CS00);
#elif	(RC5_PRESCALE==256)
	TCCR0 = (1 << CS02);
#elif	(RC5_PRESCALE==64)
	TCCR0 = (1 << CS01) | (1 << CS00);
#else
#error This RC5_PRESCALE is not supported
#endif // RC5_PRESCALE
	
	// INTx on falling edge
	// clear pending INTx
	// enable INTx interrupt
#if (RC5_INT == RC5_INT0)		
	MCUCR |=   (1 << ISC01);
	MCUCR &= ~ (1 << ISC00);
	GIFR = (1 << INTF0);
	GICR |= (1 << INT0);
#elif (RC5_INT == RC5_INT1)		
	MCUCR |=   (1 << ISC11);
	MCUCR &= ~ (1 << ISC10);
	GIFR = (1 << INTF1);
	GICR |= (1 << INT1);
#else
#error please define RC5_INT
#endif // RC5_INT
}

//////////////////////////////////////////////////////////////////////////////

SIGNAL (SIG_OVERFLOW0)
{
	TIMSK &= ~(1 << TOIE0);
	
	uint8_t _nbits = nbits;
	code_t _code = code;
	
	if (26 == _nbits)
	{
		_nbits++;
		_code.w <<= 1;
	}
	
	if (27 == _nbits 
		&& 3 == _code.agc 
		&& 0 > rc5.flip)
	{
		uint8_t _rc5_code;
		uint8_t _rc5_addr;
		// we do the bit manipulation stuff by hand, because of code size
		_rc5_code = _code.b[0] & 0x3f; // 0b00111111 : #0..#5
		_code.w <<= 2;
		_rc5_addr = _code.b[1] & 0x1f; // 0b00011111 : #6..#10
		
		if (rc5_addr & 0x80
			|| rc5_addr == _rc5_addr)
		{
			rc5.code = _rc5_code;
			rc5.addr = _rc5_addr;
			char flip = 0;
			if (_code.b[1] & 0x20) // 0b00100000 : #11
				flip = 1;
			rc5.flip = flip;
		}
	}
	
	nint = 0;
	nbits = 0;
	
	// INTx on falling edge
	// clear pending INTx
	// enable INTx interrupt
#if (RC5_INT == RC5_INT0)		
	MCUCR |=   (1 << ISC01);
	MCUCR &= ~ (1 << ISC00);
	GIFR = (1 << INTF0);
	GICR |= (1 << INT0);
#elif (RC5_INT == RC5_INT1)		
	MCUCR |=   (1 << ISC11);
	MCUCR &= ~ (1 << ISC10);
	GIFR = (1 << INTF1);
	GICR |= (1 << INT1);
#endif
}

//////////////////////////////////////////////////////////////////////////////

#if (RC5_INT == RC5_INT0)		
SIGNAL (SIG_INTERRUPT0)
#elif (RC5_INT == RC5_INT1)		
SIGNAL (SIG_INTERRUPT1)
#endif // RC5_INT
{
	code_t _code = code;
	uint8_t _nint = nint;
	
	if (0 == _nint)
	{
		// INTx on both edges
		// clear pending INTx
#if (RC5_INT == RC5_INT0)		
		MCUCR &= ~ (1 << ISC01);
		MCUCR |=   (1 << ISC00);
		GIFR = (1 << INTF0);
#elif (RC5_INT == RC5_INT1)		
		MCUCR &= ~ (1 << ISC11);
		MCUCR |=   (1 << ISC10);
		GIFR = (1 << INTF1);
#endif // RC5_INT
	
		TCNT0 = 0;
		TIFR = (1 << TOV0);
		TIMSK |= (1 << TOIE0);
		_code.w = 0;
	}
	else
	{
		uint8_t tcnt0 = TCNT0;
		
		TCNT0 = 0;
		
		// Number of bits of the just elapsed period;
		uint8_t n = 1;
		// Bits received so far
		uint8_t _nbits = nbits;
	
		// is TCNT0 close to RC5_TICKS or RC5_TICKS/2 ?
		if (tcnt0 > RC5_TICKS + RC5_DELTA)
			goto invalid;
		else if (tcnt0 < RC5_TICKS/2 - RC5_DELTA)
			goto invalid;
		else if (tcnt0 > RC5_TICKS - RC5_DELTA)
			n = 2;
		else if (tcnt0 > RC5_TICKS/2 + RC5_DELTA)
			goto invalid;
		
		//	store the just received 1 or 2 bits
		do
		{
			_nbits++;
			if (_nbits & 1)
			{
				_code.w <<= 1;
				_code.b[0] |= _nint & 1;
			}
		} 
		while (--n);
		
		if (0)
		{
			invalid:
			
			// disable INTx, run into Overflow0
#if (RC5_INT == RC5_INT0)		
			GICR &= ~(1 << INT0);
#elif (RC5_INT == RC5_INT1)		
			GICR &= ~(1 << INT1);
#endif // RC5_INT			

			_nbits = 0;
		}
		
		nbits = _nbits;
	}

	code = _code;
	nint = 1+_nint;
}

rc5.h

#ifndef _RC5_H_
#define _RC5_H_

#include <inttypes.h>

#define RC5_INT0 0
#define RC5_INT1 1

#define RC5_ALL 0xff

typedef struct
{
	uint8_t code;
	uint8_t addr;
	volatile char flip;
} rc5_t;

extern rc5_t rc5;
extern void rc5_init (uint8_t addr);

#ifdef RC5_DEBUG
extern uint16_t * const prc5_code;
extern uint8_t nbits;
extern uint8_t nint;
#endif // RC5_DEBUG

#endif /* _RC5_H_ */

Beispiele

Beispiel: Anwendung

#include <avr/io.h>
#include <avr/interrupt.h>

#include "rc5.h"

	...
	// Code atomar machen
	uint8_t sreg = SREG;
	cli();
	// Gibt's was Neues?
	if (-1 == rc5.flip)
	{
		// Nein, dann zurück	
		SREG = sreg;
		return;
	}
	// Ja, dann code merken
	uint8_t code = rc5.code;
	// und auf nächstes Zeichen warten
	rc5.flip = -1;
	SREG = sreg;
	...

Beispiel: Initialisierung

#include <avr/io.h>
#include <avr/interrupt.h>

#include "rc5.h"

	...
	// RC5 initialisieren, alle Adressen zulassen
	rc5_init (RC5_ALL);

	// Interrupts zulassen
	sei();
	...