Aus RN-Wissen.de
Wechseln zu: Navigation, Suche
Laderegler Test Tueftler Seite

Allgemein

In diesem Artikel geht es um die Programmierung des RP6 und seiner Erweiterungsplatinen RP6 CONTROL M32 und RP6 CCPRO M128 am konkreten Beispiel eines Morse-Decoders (Empfänger), eines Morse-Encoders (Sender) und einer Morse-Station (Transceiver).

Zu den Grundlagen des RP6 gibt es eine eigene Seite: RP6. Ebenso zur Programmierung des RP6 im Allgemeinen: RP6 - Programmierung


Geschichte

Nachdem Samuel Morse 1833 den ersten brauchbaren elektromagnetischen Schreibtelegrafen gebaut hatte, fand der erste Testbetrieb 1837 statt. Der verwendete Code umfasste damals nur die zehn Ziffern; die übertragenen Zahlen mussten mit Hilfe einer Tabelle in Buchstaben und Wörter übersetzt werden. Alfred Lewis Vail, ein Mitarbeiter Morses, entwickelte ab 1838 den ersten Code, der auch Buchstaben umfasste. Er bestand aus Zeichen von drei verschiedenen Längen und unterschiedlich langen Pausen. Dieser Code wurde ab 1844 betrieblich eingesetzt (als Morse Landline Code oder American Morse Code bei amerikanischen Eisenbahnen und den Telegrafenunternehmen bis in die 1960er Jahre). Die unterschiedlich langen Pausen stellten eine Unzulänglichkeit des Codes dar, so dass Friedrich Clemens Gerke ihn 1848 zur Inbetriebnahme der elektromagnetischen Telegrafenverbindung zwischen Hamburg und Cuxhaven umschrieb. Dieser Code wurde nach einigen weiteren kleinen Änderungen 1865 auf dem Internationalen Telegraphenkongress in Paris standardisiert und später mit der Einführung der drahtlosen Telegrafie als Internationaler Morsecode von der Internationalen Fernmeldeunion (ITU) genormt. Im Mai 2004 wurde der Morse Code ein zweites Mal anläßlich des 160-jährigen Bestehens der ITU ergänzt, in dem das @ (. - - . - .) offiziell hinzugefügt wurde. Die erste Änderung war ca. 1960 mit der Unterscheidung zwischen Klammer-auf (- . - - .) und Klammer-zu (- . - - . -) erfolgt. Der Morse Code hat in den letzten 10 Jahren immer mehr an Bedeutung verloren. Im Amateurfunk und zu Unterrichtszwecken wird er jedoch noch eingesetzt, auch weiterhin als (Buchstaben-) Kennung von Funknavigationsanlagen (Leuchttürme, Funkfeuer, Radarantwortbaken ...) und bei der Steuerung von Computern durch Menschen mit körperlichen Behinderungen. (Quelle: Wikipedia)


Grundlagen

Der Morse-Code verwendet drei Symbole, die Punkt (.), Strich (-) und Pause ( ) genannt werden.

  • Ein Strich (Dah) ist dreimal so lang wie ein Punkt (Dit).
  • Die Pause zwischen 2 Symbolen ist ein Dit lang.
  • Zwischen den Buchstaben eines Worts gilt eine Pause von einer Dah-Länge (= 3 Dits).
  • Die Pause zwischen Wörtern beträgt 7 Dits.

Die Übertragungsrate beim Morsen wird in Buchstaben pro Minute (BpM) oder in Wörtern pro Minute (WpM) gemessen, wobei ein Wort 5 Buchstaben entspricht. Als Referenz für die Geschwindigkeitsmessung wurde das Wort „PARIS“ ausgewählt. Gibt ein Funker dieses Wort mit seinen 5 Buchstaben 12-mal pro Minute, so beträgt die Morse-Geschwindigkeit 60 BpM. Das Wort „PARIS“ besteht aus 50 Dits (d.h. Punkt- plus Strich- plus Pausenlängen). Ein WpM sind 50 Dits pro Minute.

WpM BpM Punktlänge [ms] Strichlänge [ms]
1 5 1200 3600
5 25 240 720
10 50 120 360
20 100 60 180
50 250 24 72
100 500 12 36
150 750 8 24

Anfänger leisten bis zu 5 WpM, die Prüfgeschwindigkeit für Funkamateure liegt bei 12 WpM. Sehr gute Funker schaffen 50 WpM. Weltrekorde: Mehr als 75 WpM!


Morse-Alphabet

Das hier aufgeführte Morse-Alphabet umfasst die englischen Buchstaben und die nicht-englischen Ergänzungen zum Morse-Alphabet. Darüber hinaus gibt es Morse-Codes in vielen Sprachen, die nicht lateinische Buchstaben verwenden: Griechisch, Kyrillisch, Hebräisch, Arabisch, Persisch, Japanisch, Chinesisch, Koreanisch …

RP6 Morse-Tabelle


Morse-Baum

Mit den "Morse-Bäumen" kann man den Morse-Code lernen oder sehr langsam gesendete Morse-Zeichen direkt decodieren. Im Morse-Baum steht ein Kreis für einen Punkt und ein Rechteck mit abgerundeten Kanten für einen Strich. Beginnt das empfangene Morse-Zeichen mit einem Punkt, folgt man im Morse-Baum "E" den Pfeilen abhängig von den folgenden Punkten/Strichen bis zum Ende des Zeichens. Dort kann man dann das decodierte Zeichen ablesen. Genauso verfährt man im Morse-Baum "T" mit Morse-Zeichen, die mit einem Strich beginnen.

RP6 Morse-Baum E RP6 Morse-Baum T


Projekt

Das Empfangen und Senden von Morse-Zeichen ist für einen uC (Microcontroller) eigentlich kein Problem. Die drei Plattformen (Base, M32, M128) des RP6-Systems haben den Vorteil, dass sie aus drei unabhängigen uCs bestehen, die man zum Testen einer Datenübertragung gut benutzen kann. Dazu brauchen die M32 und M128 nur auf dem RP6 montiert zu sein. Als Verbindungen, über die die Morse-Zeichen gesendet werden, kann man die I/O-Pins benutzen, durch die die drei uCs über den XBUS schon verbunden sind (SCL, SDA, EINT1).

Natürlich kann man auch eine "echte" drahtgebundene Morse-Verbindung erreichen, indem man eine der Zusatzplatinen stand-alone betreibt und durch ein Kabel z.B. mit der Base verbindet.

Am reizvollsten ist aber eine Funkverbindung: Der HF-Sender wird z.B. mit einem Ton moduliert, wenn der Ausgangs-Pin des steuernden uCs Highpegel führt. Im HF-Empfänger wird der Eingangs-Pin des decodierenden uCs immer dann auf High-Pegel gezogen, wenn der aufmodulierte Ton empfangen wird. Das ist mit dem RP6-System und etwas Zusatz-Hardware auch für einen Nicht-Funkamateur relativ einfach machbar. Auch die im Radio z.T. noch empfangbaren Morse-Zeichen lassen sich mit einem uC decodieren. Dazu braucht man ebenfalls eine kleine Zusatz-Schaltung.

Planung

Auf allen drei Plattformen (Base, M32, M128) soll ein Morse-Sender und -Empfänger realisiert werden. Beide Funktionen sollen auch parallel nutzbar sein. Auf der RP6 Base und M32 sollen die Funktionen im üblichen Task-System der RP6 Library umgesetzt werden, damit gleichzeitig auch noch weitere Aufgaben ausgeführt werden können. Auf der CCPRO M128 soll der Morse-Sender und -Empfänger in einer 1ms-Interruptroutine parallel zum Hauptprogramm ablaufen.

Auf der M32 und M128 werden die als Morse-Code empfangenen Zeichen auf dem LC-Display dargestellt, auf der Base am Terminal. Als Morse-Code zu sendende Zeichen können an allen Plattformen am Terminal als Text eingegeben werden. Denkbar ist auch, Morse-Zeichen direkt, z.B. mit einer Morse-Taste oder alternativ sogar mit den Bumpern des RP6 einzugeben, sie zu decodieren und anzuzeigen. Viele Möglichkeiten ...

Speicherung der Morse-Zeichen

Auf einem uC ist der Speicherplatz begrenzt, daher ist es wichtig, die Morse-Zeichen möglichst kompakt zu speichern. Da sie sich im Programmablauf nicht ändern, kann man sie auch im EEPROM oder Flash-Speicher ablegen. Ich habe mich für die letzte Option entschieden.

Wie kann man die Dits (Punkte) und Dahs (Striche) am besten speichern? Das längste Morse-Zeichen ...---... (SOS) hat 9 Dits/Dahs. Es ist auch das einzige so lange Zeichen,- alle anderen kommen mit 8 Dits/Dahs hin. Wenn ich SOS nicht berücksichtige, könnte ich die Morse-Zeichen in einem Byte so speichern, dass z.B. ein 0-Bit einem Dit und ein 1-Bit einem Dah entspricht. Das Problem dieser Lösung ist, dass man nicht erkennen kann, wo ein Morse-Zeichen zuende ist. Man müßte also mit mindestens 3 weiteren Bits die Länge des Morse-Zeichens festhalten. Dann bin ich bei einem Platzbedarf pro Morse-Zeichen von 11 Bit,- bei voller Speicherung auch der Ausnahme SOS bei 13 Bit.

Überschaubarer ist es, wenn ich eine 16-Bit Konstante für jedes Morse-Zeichen verwende. Daher lege ich mich auf folgendes Verfahren fest: Ich verwende jeweils 2 Bits für jedes Dit/Dah. Dabei steht die Bitfolge "01" für ein Dit und "11" für ein Dah. Die Bitfolge "00" wird als Ende des Morse-Zeichens gedeutet. Damit kann ich alle Morse-Zeichen einfach speichern,- allerdings nun wieder ohne SOS. Das ist aber kein Problem, weil das nicht existierende Morse-Zeichen ...---.. (SOI) anstelle von SOS gespeichert werden kann. Der Encoder oder Decoder erkennt dies und macht daraus dann wieder SOS.

Beispiel: Der Buchstabe "B" sieht als Morse-Zeichen so -... (Dah-Dit-Dit-Dit) aus. Als 16-Bit Konstante würde ich das "B" dann binär als 0b0000000001010111 speichern. Das entspricht der Hexadezimalzahl 0x0057 oder dezimal 87.

Ein weiteres Beispiel: Das Ausrufezeichen (!) sieht als (nicht ITU-konformes) Morse-Zeichen so -.-.-- (Dah-Dit-Dah-Dit-Dah-Dah) aus. Als 16-Bit Konstante würde ich das "!" dann binär als 0b0000111101110111 speichern. Das entspricht der Hexadezimalzahl 0x0F77 oder dezimal 3959.

Zusätzlich zu dieser Liste der Morse-Zeichen brauche ich für den Morse-Sender noch eine weitere Liste der ASCII-Zeichen mit ihrer Zuordnung zu den Morse-Zeichen. Für Signale wird optional eine weitere Liste benötigt.

Decodierung der Morse-Zeichen

--BAUSTELLE--BAUSTELLE--BAUSTELLE--BAUSTELLE--BAUSTELLE--BAUSTELLE--BAUSTELLE--BAUSTELLE--BAUSTELLE--

Encodierung der Morse-Zeichen

Libraries

RP6 Base

Header

/* ****************************************************************************
 *                           _______________________
 *                           \| RP6  ROBOT SYSTEM |/
 *                            \_-_-_-_-_-_-_-_-_-_/         >>> BASE CONTROLLER
 * ----------------------------------------------------------------------------
 * ------------------------ [c]2012 - Dirk ------------------------------------
 * ****************************************************************************
 * File: RP6BaseMorseLib.h
 * Version: 3.3w
 * Target: RP6 Base - ATMEGA32 @8.00MHz
 * Author(s): Dirk
 * ****************************************************************************
 * Description:
 * This is the RP6BaseMorse library header file.
 * You have to include this file, if you want to use the library
 * RP6BaseMorseLib.c in your own projects.
 *
 * ****************************************************************************
 * THE CHANGELOG CAN BE FOUND AT THE END OF THIS FILE!
 * ****************************************************************************
 */

#ifndef RP6BASEMORSE_H
#define RP6BASEMORSE_H

/*****************************************************************************/
// Includes:

#include "RP6RobotBaseLib.h" 	// The RP6 Robot Base Library.
								// Always needs to be included!

/*****************************************************************************/
// Defines:

#define SPEED						100		// = 12 WpM = 60 CpM
// Calculate SPEED: SPEED = 1200 / WpM
//                  SPEED = 6000 / CpM
#define SPEED_MIN					400		// = 3 WpM = 15 CpM
#define SPEED_MAX					8		// = 150 WpM = 750 CpM
#define SPEED_VAR					5		// Decoder speed variation

#define LIMITED_PAUSE						// Decoder: Spaces limited
#define SPACE_CNT_LIMIT				3		// Max. number of spaces

//#define DEBUG								// Decoder debug mode

#define LINE_LENGTH					32		// Terminal line length

#define LIGHT								// Use LED1 to show Morse sign 

#define MS_SIGNALS_MAXINDEX			7
#define MS_SPECIALS_MAXINDEX		25
#define MORSESIGNS_MAXINDEX			79

// Flash constants (Morse tables):
const uint16_t ms_ft[MORSESIGNS_MAXINDEX + 1];
const uint8_t ms_a0uc_ft[MORSESIGNS_MAXINDEX + 1];
const uint8_t ms_a1uc_ft[MORSESIGNS_MAXINDEX + 1];
const uint8_t ms_a2uc_ft[MORSESIGNS_MAXINDEX + 1];
const uint8_t a_ms_ft[256];

#define MORSEDEC_BUFFER_MAXINDEX	31		// Morse decoder buffer length
#define MORSEENC_BUFFER_MAXINDEX	31		// Morse encoder buffer length

// Morse decoder/encoder status:
#define MORSE_BUFFER_OK				0
#define MORSE_BUFFER_OVERFLOW		1		// Morse buffer overflow

/*****************************************************************************/
// Variables:

extern uint8_t morsedec_status;
extern uint8_t morseenc_status;
extern uint8_t morse_error;

char morsedec_buffer[MORSEDEC_BUFFER_MAXINDEX + 2];
uint8_t dec_write_pos, dec_read_pos;
char morseenc_buffer[MORSEENC_BUFFER_MAXINDEX + 2];
uint8_t enc_write_pos, enc_read_pos;

uint16_t decspeed;
uint8_t speedvar;

uint16_t encspeed;

#ifdef DEBUG
uint16_t ditlength, dahlength;
#endif

/*****************************************************************************/
// Functions:

uint8_t Lower2UpperCase(uint8_t);
uint8_t Upper2LowerCase(uint8_t);

uint16_t MsIndex2MorseCode(uint8_t);
uint8_t MorseCode2MsIndex(uint16_t);
void MorseCode2MsName(char *, uint16_t);
uint8_t MsName2MsIndex(char *);

void MorseCode2MorseSign(char *, uint16_t);
uint16_t MorseSign2MorseCode(char *);

void clearMorseDecBuffer(void);
void initMorseDecoder(void);
void storeMsChar2DecBuffer(uint8_t);
void task_MorseDec(void);
uint8_t readMorseChar(void);
uint8_t readMorseChars(char *, uint8_t);
uint8_t getMorseDecBufferLength(void);

void initMorseEncoder(void);
uint8_t fetchMsIndexFromEncBuffer(void);
void task_MorseEnc(void);
void storeMsIndex2EncBuffer(uint8_t);
void pauseMorse(uint8_t);
void writeMorseChar(uint8_t);
void writeMorseString(char *);
uint8_t getMorseEncBufferLength(void);

#ifndef DEBUG
void writeMorse(void);
#else
void writeDebugInfo(void);
#endif


#endif

/******************************************************************************
 * Additional info
 * ****************************************************************************
 * Changelog:
 * 
 *  ---> changes are documented in the file "RP6BaseMorseLib.c"
 *
 * ****************************************************************************
 */

/*****************************************************************************/
// EOF

Library

/* ****************************************************************************
 *                           _______________________
 *                           \| RP6  ROBOT SYSTEM |/
 *                            \_-_-_-_-_-_-_-_-_-_/         >>> BASE CONTROLLER
 * ----------------------------------------------------------------------------
 * ------------------------ [c]2012 - Dirk ------------------------------------
 * ****************************************************************************
 * File: RP6BaseMorseLib.c
 * Version: 3.3w
 * Target: RP6 Base - ATMEGA32 @8.00MHz
 * Author(s): Dirk
 * ****************************************************************************
 * Description:
 *
 * The RP6 Base Morse Library.
 *
 * ****************************************************************************
 * ATTENTION: The 100us timer is used for the Morse decoder and encoder
 *            task! Please do not alter the variable "timer" elsewhere in
 *            your program!
 *
 * ****************************************************************************
 * THE CHANGELOG CAN BE FOUND AT THE END OF THIS FILE!
 * ****************************************************************************
 */
 
/*****************************************************************************/
// Includes:

#include "RP6BaseMorseLib.h"

/*****************************************************************************/
// Defines:

// RP6 Base Morse Decoder Connection (input):
#define MORSEDEC_PORT	PORTC
#define MORSEDEC_DDR	DDRC
#define MORSEDEC_PIN	PINC
//#define MORSEDEC_IN		SCL					// PINC0  XBUS Pin 10
#define MORSEDEC_IN		SDA					// PINC1  XBUS Pin 12

//#define MORSEDEC_PORT	PORTA
//#define MORSEDEC_DDR	DDRA
//#define MORSEDEC_PIN	PINA
//#define MORSEDEC_IN		E_INT1				// PINA4  XBUS Pin 8

// RP6 Base Morse Encoder Connection (output):
//#define MORSEENC_PORT	PORTC
//#define MORSEENC_DDR	DDRC
//#define MORSEENC_PIN	PINC
//#define MORSEENC_IN		SCL					// PINC0  XBUS Pin 10
//#define MORSEENC_IN		SDA					// PINC1  XBUS Pin 12

#define MORSEENC_PORT	PORTA
#define MORSEENC_DDR	DDRA
#define MORSEENC_PIN	PINA
#define MORSEENC_IN		E_INT1				// PINA4  XBUS Pin 8

// ----------------------------------------------------------------------------
// MORSE TABLES:

// Morse Table [0..79]:
// Morse decoders and encoders use this table for receiving or sending Morse
// code. This table consists of 16-bit constants. Each table index [0..79]
// (or each word constant) represents one Morse sign.
// The dots (dit) and the dashes (dah) are stored as two bits: The bits "01"
// stand for a dit and "11" for a dah, read from right to left in the binary
// notation. Between dits and dahs of a Morse sign you have to send a pause
// with the length of one dit. Between Morse signs there is a pause with the
// length of three dits (or one dah).
//
// Example:                     End <<<<7<<6<<5<<4<<3<<2<<1<<<< Start
//                                  ---DahDitDitDahDitDitDit
// 0x35D5 = 0b0011010111010101 -> 0b 00 11 01 01 11 01 01 01 -> $ (Dollar)
const uint16_t ms_ft[] PROGMEM =
// Signals (prosigns):
// Hex		  Binary		   Sign	   Index  Prosign
{0x5555, // 0b0101010101010101			 0		HH
 0x0DD5, // 0b0000110111010101					SK
 0x0377, // 0b0000001101110111					CT
 0x3757, // 0b0011011101010111					BK
 0x5D77, // 0b0101110101110111					CL
 0xDF77, // 0b1101111101110111			 5		CQ
 0x0FD7, // 0b0000111111010111					DO
 0x5FD5, // 0b0101111111010101			 7		SOS
//------------------------------------------------------
// Special characters:
// Hex		  Binary		   Sign	   Index  Prosign
 0x01DF, // 0b0000000111011111  ^G		 8
 0x00FF, // 0b0000000011111111  CH,^H
 0x01FD, // 0b0000000111111101  ^J		10
 0x15D5, // 0b0001010111010101  /S
 0x01D5, // 0b0000000111010101  ^S				VE
 0x075F, // 0b0000011101011111  /Z
 0x035F, // 0b0000001101011111  .Z
 0x037D, // 0b0000001101111101  /A,°A	15
 0x00DD, // 0b0000000011011101  Ä				AA
 0x0177, // 0b0000000101110111  C~
 0x035D, // 0b0000001101011101  \E
 0x0175, // 0b0000000101110101  /E
 0x01F5, // 0b0000000111110101  Eth		20
 0x03DF, // 0b0000001111011111  ~N
 0x007F, // 0b0000000001111111  Ö
 0x00F5, // 0b0000000011110101  Ü
 0x017D, // 0b0000000101111101  Thorn
 0x17D5, // 0b0001011111010101  ß		25
//------------------------------------------------------
// Normal characters:
// Hex		  Binary		   Sign	   Index  Prosign
 0x0F77, // 0b0000111101110111  !		26
 0x075D, // 0b0000011101011101  "
 0x35D5, // 0b0011010111010101  $
 0x015D, // 0b0000000101011101  &				AS
 0x07FD, // 0b0000011111111101  '		30
 0x01F7, // 0b0000000111110111  (				KN
 0x0DF7, // 0b0000110111110111  )
 0x01DD, // 0b0000000111011101  +				AR
 0x0F5F, // 0b0000111101011111  ,
 0x0D57, // 0b0000110101010111  -		35
 0x0DDD, // 0b0000110111011101  .
 0x01D7, // 0b0000000111010111  /				NR
 0x03FF, // 0b0000001111111111  0
 0x03FD, // 0b0000001111111101  1
 0x03F5, // 0b0000001111110101  2		40
 0x03D5, // 0b0000001111010101  3
 0x0355, // 0b0000001101010101  4
 0x0155, // 0b0000000101010101  5
 0x0157, // 0b0000000101010111  6
 0x015F, // 0b0000000101011111  7		45
 0x017F, // 0b0000000101111111  8
 0x01FF, // 0b0000000111111111  9
 0x057F, // 0b0000010101111111  :
 0x0777, // 0b0000011101110111  ;
 0x0357, // 0b0000001101010111  =		50		BT
 0x05F5, // 0b0000010111110101  ?				IMI
 0x077D, // 0b0000011101111101  @
 0x000D, // 0b0000000000001101  A
 0x0057, // 0b0000000001010111  B				DE
 0x0077, // 0b0000000001110111  C		55
 0x0017, // 0b0000000000010111  D
 0x0001, // 0b0000000000000001  E
 0x0075, // 0b0000000001110101  F
 0x001F, // 0b0000000000011111  G
 0x0055, // 0b0000000001010101  H		60
 0x0005, // 0b0000000000000101  I
 0x00FD, // 0b0000000011111101  J
 0x0037, // 0b0000000000110111  K				K
 0x005D, // 0b0000000001011101  L
 0x000F, // 0b0000000000001111  M		65
 0x0007, // 0b0000000000000111  N
 0x003F, // 0b0000000000111111  O
 0x007D, // 0b0000000001111101  P
 0x00DF, // 0b0000000011011111  Q
 0x001D, // 0b0000000000011101  R		70		R
 0x0015, // 0b0000000000010101  S
 0x0003, // 0b0000000000000011  T
 0x0035, // 0b0000000000110101  U
 0x00D5, // 0b0000000011010101  V
 0x003D, // 0b0000000000111101  W		75
 0x00D7, // 0b0000000011010111  X
 0x00F7, // 0b0000000011110111  Y
 0x005F, // 0b0000000001011111  Z
 0x0DF5};// 0b0000110111110101  _		79
// Remarks: - SOS (Morse sign ...---...) can not be stored in a 16-bit
//            constant because SOS is the only Morse sign with 9 dits/dahs.
//            So SOS is stored as the (not existing) Morse sign ...---..
//            (SOI) and must be treated special in decoders/encoders.  


// Morse-ASCII-Table [0..79]:
// Morse decoders use this table for receiving Morse code.
const uint8_t ms_a0uc_ft[] PROGMEM = 
//H   S   C   B    C   C   D   S
{104,115, 99, 98, 99, 99,100,115,
//0                    5
//^   C   ^   %    ^   %   *   /A  Ä   C~  \E  /E  Et  ~N   Ö   Ü  To   ß
  94, 99, 94, 37, 94, 37, 42,193,196,199,200,201,208,209,214,220,222,223,
//        10                   15                  20                   25
//!  "  $  &  '  (  )   +  ,  -  .  /  0  1  2   3  4  5  6  7  8  9  :  ;
 33,34,36,38,39,40,41,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,
//            30             35              40             45
//=  ?  @  A  B  C   D   E    F   G   H   I   J   K   L   M   N   O    P   Q
 61,63,64,65,66,67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, 81,
//50            55                   60                   65
// R  S   T   U   V   W   X   Y    Z   _  
  82, 83, 84, 85, 86, 87, 88, 89, 90,95};		// Et = Eth,  To = Thorn
//70                  75              79

const uint8_t ms_a1uc_ft[] PROGMEM = 
//H   K   T   K    L   Q   O   O
{104,107,116,107,108,113,111,111,
//0                    5
//G   H   J   S    S   Z   Z
 103,104,106,115,115,122,122, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//        10                   15                  20                   25
 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,
//            30             35              40             45
 32,32,32,32,32,32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//50            55                   60                   65
  32, 32, 32, 32, 32, 32, 32, 32, 32,32};		// Et = Eth,  To = Thorn
//70                  75              79

const uint8_t ms_a2uc_ft[] PROGMEM = 
//                             S
{ 32, 32, 32, 32, 32, 32, 32,115,
// 0                   5
  32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//        10                   15                  20                   25
 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,
//            30             35              40             45
 32,32,32,32,32,32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//50            55                   60                   65
  32, 32, 32, 32, 32, 32, 32, 32, 32,32};		// Et = Eth,  To = Thorn
//70                  75              79
// Prosigns and special characters are stored as lower case letters (hh,
// sk, ^g, ch ...) in this table.
// Remarks: - The special chars  ^G, ^J, /S, ^S, /Z, .Z [indices 8, 10..14]
//            are represented as ^g, ^j, %s, ^s, %z, *z in this table.
//          - If Morse decoders receive a pause with the length of 7 dits,
//            they have to give out the ASCII code ' ' (space [32]).


// ASCII-Morse-Table [0..255]:
// Morse encoders use this table to send Morse code.
const uint8_t a_ms_ft[] PROGMEM =
{51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//0              5              10              15             20
 51,51,51,51,51,51,51,51,
//24                30
//_  !  "  ?  $  ?  &  '  (  )   X  +  ,  -  .  /  0  1   2  3  4  5  6  7
 79,26,27,51,28,51,29,30,31,32,76,33,34,35,36,37,38,39,40,41,42,43,44,45,
//32       35             40              45             50              55
//8  9  :  ;  ?  =  ?  ?   @  A  B  C  D  E  F  G  H   I  J  K  L  M  N  O
 46,47,48,49,51,50,51,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,
//56          60             65              70              75
//P  Q  R  S  T  U  V  W  X   Y  Z  [  ?  ]  ?  _   ?  A  B  C  D  E  F  G
 68,69,70,71,72,73,74,75,76,77,78,31,51,32,51,79,51,53,54,55,56,57,58,59,
//80             85             90              95             100
//H  I  J  K  L  M  N  O   P  Q  R  S  T  U  V  W   X  Y  Z  {  ?  }  ?  ?
 60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,31,51,32,51,51,
//104              110             115            120             125
//?  ?  ?  ?  ?  ?  ?  ?   ?  ?  ?  ?  ?  ?  ?  ?  ?   ?  ?  ?  ?  ?  ?  ?
 51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//128  130            135             140            145             150
//?  ?  ?  ?  ?  ?  ?  ?   _  ?  ?  ?  ?  ?  ?  ?  ?   ?  ?  ?  ?  ?  ?  ?
 51,51,51,51,51,51,51,51,79,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//152     155            160             165             170            175
//?  ?  ?  ?  ?  ?  ?  ?  ?   ?  ?  ?  ?  ?  ?  ?  ?  /A  ?  ?  Ä  ?  ?  C~
 51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,15,51,51,16,51,51,17,
//176        180             185            190             195
//\E/E  ?  ?  ?  ?  ?  ?  Et ~N  ?  ?  ?  ?  Ö  X   ?  ?  ?  ?  Ü  ?  To ß
 18,19,51,51,51,51,51,51,20,21,51,51,51,51,22,76,51,51,51,51,23,51,24,25,
//200           205             210            215             220
//? /A  ?  ?  Ä  ?  ?  C~ \E /E  ?  ?  ?  ?  ?  ?  Et ~N  ?  ?  ?  ?  Ö  /
 51,15,51,51,16,51,51,17,18,19,51,51,51,51,51,51,20,21,51,51,51,51,22,37,
//224              230             235            240             245
//?  ?  ?  ?  Ü  ?  To ?
 51,51,51,51,23,51,24,51};					// Et = Eth,  To = Thorn
//248                 255
// Remarks: - ASCII codes 91 '[' and 123 '{' are converted to Morse
//            code '(' [31].
//          - ASCII codes 93 ']' and 125 '}' are converted to Morse
//            code ')' [32].
//          - ASCII code 215 (multiplication sign) is converted to
//            Morse code 'X' [76].
//          - ASCII code 247 (division sign) is converted to Morse
//            code '/' [37].
//          - ASCII codes 32 (sp) and 160 (nbsp) are represented as
//            '_' [79] in this table but must be treated special in
//            encoders: The Morse encoder has to send a pause with
//            the length of 7 dits for a space.
//          - All non printable ASCII codes [0..31] and other codes
//            not defined in the Morse code are converted to Morse
//            code '?' [51].

// MORSE TABLES (END)
// ----------------------------------------------------------------------------

/*****************************************************************************/
// Variables:

uint8_t morsedec_status;
uint8_t morseenc_status;
uint8_t morse_error;

/*****************************************************************************/
// Functions:

/**
 * Convert lower case to upper case letters
 *
 * Input:  ASCII code [0..255]
 * Output: ASCII code, only with upper case letters
 *
 */
uint8_t Lower2UpperCase(uint8_t ch)
{uint8_t chuc;
	chuc = ch;
	if ((ch >= 97) && (ch <= 122)) {
		chuc -= 32;
	}
	if ((ch >= 224) && (ch <= 254) && (ch != 247)) {
		chuc -= 32;
	}
	return (chuc);
}

/**
 * Convert upper case to lower case letters
 *
 * Input:  ASCII code [0..255]
 * Output: ASCII code, only with lower case letters
 *
 */
uint8_t Upper2LowerCase(uint8_t ch)
{uint8_t chlc;
	chlc = ch;
	if ((ch >= 65) && (ch <= 90)) {
		chlc += 32;
	}
	if ((ch >= 192) && (ch <= 222) && (ch != 215)) {
		chlc += 32;
	}
	return (chlc);
}

/**
 * Output the Morse code of a Morse table index
 *
 * Input:  Morse table index [0..MORSESIGNS_MAXINDEX]
 * Output: Morse code (See table ms_ft[] above!)
 *
 */
uint16_t MsIndex2MorseCode(uint8_t msindex)
{
	morse_error = false;
	return (pgm_read_word(&ms_ft[msindex]));
}

/**
 * Output the table index of a Morse code
 *
 * Input:  Morse code (See table ms_ft[] above!)
 * Output: Morse table index [0..MORSESIGNS_MAXINDEX]
 *
 */
uint8_t MorseCode2MsIndex(uint16_t morsecode)
{uint8_t msidx;
	for (msidx = 0; msidx <= MORSESIGNS_MAXINDEX; msidx++) {
		if (morsecode == pgm_read_word(&ms_ft[msidx])) {break;}
	}
	if (msidx <= MORSESIGNS_MAXINDEX) {
		morse_error = false;
		return (msidx);					// Morse table index
	}
	else {
		morse_error = true;				// Unknown Morse code:
		return (51);					//  Return table index of '?'
	}
}

/**
 * Output the Morse sign name of a Morse code
 *
 * Input:  Morse code (See table ms_ft[] above!)
 * Output: String with Morse sign name (1..3 ASCII letters)
 *
 */
void MorseCode2MsName(char *msname, uint16_t morsecode)
{uint8_t msidx;
	msidx = MorseCode2MsIndex(morsecode);
	msname[0] = pgm_read_byte(&ms_a0uc_ft[msidx]);
	msname[1] = pgm_read_byte(&ms_a1uc_ft[msidx]);
	if (msname[1] == 32) {msname[1] = '\0';}
	msname[2] = pgm_read_byte(&ms_a2uc_ft[msidx]);
	if (msname[2] == 32) {
		msname[2] = '\0';
	}
	else {
		msname[3] = '\0';
	}
}

/**
 * Output the Morse table index of a Morse sign name
 *
 * Input:  String with Morse sign name (1..3 ASCII letters)
 * Output: Morse table index [0..MORSESIGNS_MAXINDEX]
 *
 */
uint8_t MsName2MsIndex(char *msname)
{uint8_t msidx;
	for (msidx = 0; msidx <= MORSESIGNS_MAXINDEX; msidx++) {
		if (msname[0] == pgm_read_byte(&ms_a0uc_ft[msidx])) {
			if ((pgm_read_byte(&ms_a1uc_ft[msidx]) == 32)
			 || (msname[1] == pgm_read_byte(&ms_a1uc_ft[msidx]))) {
				if ((pgm_read_byte(&ms_a2uc_ft[msidx]) == 32)
				 || (msname[2] == pgm_read_byte(&ms_a2uc_ft[msidx]))) {
					break;
				}
			}
		}
	}
	if (msidx <= MORSESIGNS_MAXINDEX) {
		morse_error = false;
		return (msidx);					// Morse table index
	}
	else {
		morse_error = true;				// Unknown Morse sign name:
		return (51);					//  Return table index of '?'
	}
}

/**
 * Output the Morse sign of a Morse code
 *
 * Input:  Morse code (See table ms_ft[] above!)
 * Output: String with the Morse sign (1..9 dits [.] or dahs [-])
 *
 * Example: $  -> 0b0011010111010101  -> Morse sign ...-..-
 *
 */
void MorseCode2MorseSign(char *morsesign, uint16_t morsecode)
{uint8_t i; uint16_t ms_code;
	ms_code = morsecode;
	i = 0;
	do {
		switch (ms_code & 3) {
			case 1 :					// dit!
				morsesign[i] = '.';
				i++; break;
			case 3 :					// dah!
				morsesign[i] = '-';
				i++;
		}
		ms_code >>= 2;
	} while (ms_code);
	if (morsecode == 0x5FD5) {			// SOS: Add last dit!
		morsesign[i] = '.';
		i++;
	}
	morsesign[i] = '\0';
	morse_error = false;
}

/**
 * Output the Morse code of a Morse sign
 *
 * Input:  String with the Morse sign (1..9 dits [.] or dahs [-])
 * Output: Morse code (See table ms_ft[] above!)
 *
 * Example: $  -> Morse sign ...-..-  -> 0b0011010111010101
 *
 */
uint16_t MorseSign2MorseCode(char *morsesign)
{uint8_t i, ch; uint16_t ms_code;
	ms_code = 0;
	ch = 1;
	for (i = 0; i <= 7; i++) {
		ms_code >>= 2;
		if (ch) {
			ch = morsesign[i];
			switch (ch) {
				case '.' :					// dit!
					ms_code |= 0x4000; break;
				case '-' :					// dah!
					ms_code |= 0xC000;
			}
		}
		
	}
	if ((ms_code == 0x5FD5) && (morsesign[8] != '.')) {
		ms_code = 0x05F5;	// SOS: If last dit doesn't exist, return '?'!
		morse_error = true;
	}
	else {
		morse_error = false;
	}
	return (ms_code);
}

/*****************************************************************************/
// Morse decoder functions:

/**
 * Clear the Morse decoder ring buffer
 *
 */
void clearMorseDecBuffer(void)
{
	morsedec_status = MORSE_BUFFER_OK;		// Decoder buffer status ok
	dec_write_pos = 255;					// Reset buffer write position
	dec_read_pos = 255;						// Reset buffer read position
}

/**
 * Init Morse Decoder
 *
 * Call this once before using the Morse decoder (receiver) task!
 *
 */
void initMorseDecoder(void)
{
	MORSEDEC_DDR &= ~MORSEDEC_IN;			// Decoder input pin
	MORSEDEC_PORT |= MORSEDEC_IN;			// MORSEDEC_IN -> Pullup
	morse_error = false;					// Reset Morse error flag
	clearMorseDecBuffer();					// Clear the decoder buffer
	decspeed = SPEED;						// Decoder speed
	speedvar = SPEED_VAR;					// Decoder speed variation
}

/**
 * Store a decoded (prosign) Morse sign char into the decoder ring buffer
 *
 * Input: ASCII char (part of a string with the (pro)sign name)
 *
 */
void storeMsChar2DecBuffer(uint8_t ch)
{
	if (getMorseDecBufferLength() < MORSEDEC_BUFFER_MAXINDEX) {
		dec_write_pos++;
		if (dec_write_pos > MORSEDEC_BUFFER_MAXINDEX) {
			dec_write_pos = 0;
		}
		morsedec_buffer[dec_write_pos] = ch;
		morsedec_status = MORSE_BUFFER_OK;	// Decoder buffer status ok
	}
	else {
		morsedec_status = MORSE_BUFFER_OVERFLOW;// Decoder buffer overflow
	}
}

/**
 * Morse decoder task
 *
 */
void task_MorseDec(void)
{uint16_t time_100usecs;
 static char ms_sign[10]; uint8_t temp;
 static uint16_t last_timer, signal, pause;
 static uint8_t ditdah, ditdah_cnt;
 char ms_name[4]; 
#ifdef LIMITED_PAUSE
 static uint8_t space_cnt;
#endif 
	time_100usecs = timer - last_timer;
	last_timer += time_100usecs;
	temp = MORSEDEC_PIN & MORSEDEC_IN;		// Read Morse level
	if (temp) {								// Signal on
#ifdef LIGHT
		statusLEDs.LED1 = true;
		updateStatusLEDs();
#endif
		signal += time_100usecs;
		if (pause > (decspeed * 20)) {		// Pause > 2 dits:
			if (ditdah) {					//  Morse sign end (length 3 dits)
				ms_sign[ditdah_cnt] = ditdah;
				ditdah_cnt++;
				ms_sign[ditdah_cnt] = '\0';
				ditdah_cnt = 0;
				ditdah = 0;
				MorseCode2MsName(ms_name, MorseSign2MorseCode(ms_sign));
				temp = 0;
				while (ms_name[temp]) {
					storeMsChar2DecBuffer(ms_name[temp++]);
				}
			}
			pause = 0;
		}
		if (pause) {						// Short pause: 
			if (ditdah) {					//  Dit or dah end (length 1 dit)
				ms_sign[ditdah_cnt] = ditdah;
				ditdah_cnt++;
				ms_sign[ditdah_cnt] = '\0';
				if (ditdah_cnt > 8) {ditdah_cnt = 0;}
				ditdah = 0;
			}
			pause = 0;
		}
	}
	else {									// Signal off (pause)
#ifdef LIGHT
		statusLEDs.LED1 = false;
		updateStatusLEDs();
#endif
		pause += time_100usecs;
		if (pause > (decspeed * 50)) {		// Pause > 5 dits:
			if (ditdah) {					//  Space or longer pause
				ms_sign[ditdah_cnt] = ditdah;
				ditdah_cnt++;
				ms_sign[ditdah_cnt] = '\0';
				ditdah_cnt = 0;
				ditdah = 0;
				MorseCode2MsName(ms_name, MorseSign2MorseCode(ms_sign));
				temp = 0;
				while (ms_name[temp]) {
					storeMsChar2DecBuffer(ms_name[temp++]);
				}
#ifdef LIMITED_PAUSE
				space_cnt = SPACE_CNT_LIMIT;
				space_cnt--;
#endif
				storeMsChar2DecBuffer(' ');		// Add a space after a sign
				pause = 0;
			}
#ifdef LIMITED_PAUSE
			if (space_cnt) {
#endif
				if (pause >= (decspeed * 70)) {// Pause >= 7 dits:
					storeMsChar2DecBuffer(' '); // Add spaces while pause
					pause -= (decspeed * 70);
#ifdef LIMITED_PAUSE
					space_cnt--;
#endif
				}
#ifdef LIMITED_PAUSE
			}
			else {
				pause = 0;
			}
#endif
		}
		if (signal > (decspeed * 20)) {	// Signal > 2 dits:
#ifdef DEBUG
			dahlength = signal;
#endif
			ditdah = '-';					//  Dah (length 3 dits)!
			if (signal >= (decspeed * 33)) {// Signal >= 3.3 dits (+10%):
				decspeed += speedvar;		//   Reduce decoder speed
				if (decspeed > SPEED_MIN) {decspeed = SPEED_MIN;}
			}
			signal = 0;
		}
		if (signal) {						// Short signal:
#ifdef DEBUG
			ditlength = signal;
#endif
			ditdah = '.';					//  Dit!
			if (signal <= (decspeed * 9)) {// Signal <= 0.9 dits (-10%):
				decspeed -= speedvar;		//  Increase decoder speed
				if (decspeed < SPEED_MAX) {decspeed = SPEED_MAX;}
			}
			signal = 0;
		}
	}
}

/**
 * Read next character from the Morse decoder ring buffer
 *
 * Output: Printable ASCII character [32..255] (as part of
 *         a received/decoded (prosign) Morse sign name)
 *         OR 0 (false), if the ring buffer is empty
 *
 */
uint8_t readMorseChar(void)
{uint8_t ch;
	if (dec_read_pos != dec_write_pos) {
		dec_read_pos++;
		if (dec_read_pos > MORSEDEC_BUFFER_MAXINDEX) {
			dec_read_pos = 0;
		}
		ch = morsedec_buffer[dec_read_pos];
	}
	else {
		ch = 0;
	}
	return (ch);
}

/**
 * Read next [numberOfChars] characters from the Morse decoder ring buffer
 *
 * Output: Number of characters copied to *buf,
 *         string *buf with the copied characters
 *
 */
uint8_t readMorseChars(char *buf, uint8_t numberOfChars)
{uint8_t ch, i;
	i = 0;
	while (i < numberOfChars) {
		ch = readMorseChar();
		if (ch) {
			buf[i] = ch;
		}
		else {break;}
		i++;
	}
	buf[i] = '\0';
	return (i);
}

/**
 * Get the number of characters still in the Morse decoder ring buffer
 *
 * Output: Number of characters (0: Buffer is empty!)
 *
 */
uint8_t getMorseDecBufferLength(void)
{int16_t dec_posdiff;
	dec_posdiff = dec_write_pos - dec_read_pos;
	if (dec_posdiff < 0) {
		dec_posdiff += (MORSEDEC_BUFFER_MAXINDEX + 1);
	}
	return ((uint8_t) dec_posdiff);
}

/*****************************************************************************/
// Morse encoder functions:

/**
 * Init Morse Encoder
 *
 * Call this once before using the Morse encoder (sender) task!
 *
 */
void initMorseEncoder(void)
{
	MORSEENC_DDR |= MORSEENC_IN;			// Encoder output pin
	MORSEENC_PORT &= ~MORSEENC_IN;			// Output low
	morse_error = false;					// Reset Morse error flag
	morseenc_status = MORSE_BUFFER_OK;		// Encoder buffer status ok
	enc_write_pos = 255;					// Reset buffer write pointer
	enc_read_pos = 255;						// Reset buffer read pointer
	encspeed = SPEED;						// Set encoder speed
}

/**
 * Fetch next Morse table index from the Morse encoder ring buffer
 *
 * Output: Morse table index [0..MORSESIGNS_MAXINDEX(..127)]
 *         OR pause length [129..255] (pause 1..127 dits)
 *         OR 128 (0x80), if the ring buffer is empty
 *
 */
uint8_t fetchMsIndexFromEncBuffer(void)
{uint8_t msidx;
	if (enc_read_pos != enc_write_pos) {
		enc_read_pos++;
		if (enc_read_pos > MORSEENC_BUFFER_MAXINDEX) {
			enc_read_pos = 0;
		}
		msidx = morseenc_buffer[enc_read_pos];
	}
	else {
		msidx = 0x80;
	}
	return (msidx);
}

/**
 * Morse encoder task
 *
 */
void task_MorseEnc(void)
{static uint8_t busy_flag, signal_flag, pause_flag, sos_flag, pause_dits;
 static uint16_t last_timer, ms_code; uint8_t msidx;
	if (busy_flag) {						// Encoder busy!
		if (signal_flag) {					// Sending signal
			if (!pause_flag) {				// Waiting for signal end
				if ((timer - last_timer)
				 >= (encspeed * 10 * (ms_code & 3))) {
#ifdef LIGHT
					statusLEDs.LED1 = false;
					updateStatusLEDs();
#endif
					MORSEENC_PORT &= ~MORSEENC_IN;
					last_timer = timer;
					pause_flag = true;
					ms_code >>= 2;
				}
			}
			else {							// Pause after a signal
				if (ms_code) {				// Dit/dah (signal) end:
					if ((timer - last_timer) >= (encspeed * 10)) {
						signal_flag = false;//  Pause 1 dit
					}
				}
				else {						// Morse sign end:
					if (sos_flag) {			//  Case SOS:
						ms_code = 0x0001;	//   Add last dit
						sos_flag = false;
					}
					else {					//  Case sign end:
						if ((timer - last_timer) >= (encspeed * 30)) {
							busy_flag = false;// Pause 3 dits
						}
					}
				}
			}
		}
		else {								// Signal end
			if (pause_dits) {				// Make a longer pause
				if ((timer - last_timer) >= (encspeed * 10 * pause_dits)) {
					busy_flag = false;		// Longer pause end
				}
			}
			else {							// Start new signal (dit/dah)
#ifdef LIGHT
				statusLEDs.LED1 = true;
				updateStatusLEDs();
#endif
				MORSEENC_PORT |= MORSEENC_IN; 
				last_timer = timer;
				pause_flag = false;
				signal_flag = true;
			}
		}
	}
	else {									// Encoder not busy!
		msidx = fetchMsIndexFromEncBuffer();// Get next index to send
		if (msidx == 0x80) {				//  from the ring buffer
			return;							// Buffer empty: Return
		}
		else {
			if (msidx < 0x80) {				// Morse sign to send
				ms_code = MsIndex2MorseCode(msidx);
				if (ms_code == 0x5FD5) {
					sos_flag = true;		// Sign is SOS
				}
				else {
					sos_flag = false;
				}
				pause_dits = 0;
			}
			else {							// (msidx > 0x80): Longer pause
				last_timer = timer;
				pause_dits = msidx - 0x80;
			}
			signal_flag = false;
			busy_flag = true;				// Sign / longer pause can be sent
		}
	}
}

/**
 * Store a Morse table index into the Morse encoder ring buffer
 *
 * Input: Morse table index [0..MORSESIGNS_MAXINDEX(..127)]
 *        OR pause length [129..255] (pause 1..127 dits)
 *
 */
void storeMsIndex2EncBuffer(uint8_t msindex)
{
	if (getMorseEncBufferLength() < MORSEENC_BUFFER_MAXINDEX) {
		enc_write_pos++;
		if (enc_write_pos > MORSEENC_BUFFER_MAXINDEX) {
			enc_write_pos = 0;
		}
		morseenc_buffer[enc_write_pos] = msindex;
		morseenc_status = MORSE_BUFFER_OK;	// Encoder buffer status ok
	}
	else {
		morseenc_status = MORSE_BUFFER_OVERFLOW; // Encoder buffer overflow
	}
}

/**
 * Write a pause length to send into the Morse encoder ring buffer
 *
 * Input: Pause length [1..127 dits] (0.14..18.14 spaces)
 *
 * With this function you can reach longer pauses.
 *   Examples:
 *   pauseMorse(7);  is identical with  writeMorseChar(' ');
 *   pauseMorse(14); is identical with  writeMorseString("  ");
 * The function pauseMorse(len) only writes one byte into the encoder ring
 * buffer for a longer pause, while writeMorseChar(' ') writes one byte for
 * each space to send. You should use writeMorseChar(' ') for single spaces
 * (between words) and pauseMorse(len) for longer pauses.
 *
 * ATTENTION: !-----------------------------------------------------------!
 *            ! The max. pause length you can reach with this function is !
 *            ! about 6 seconds! So the max. input value of this function !
 *            ! depends on encspeed!!!                                    !
 *            !-----------------------------------------------------------!
 *            !   ==>  Max. pause length [dits] = 6000 / encspeed  <==    !
 *            !-----------------------------------------------------------!
 *            For encspeeds from 8 (SPEED_MAX) to 47 the max. pause length
 *            is 127 dits. For encspeeds from 48 to 400 (SPEED_MIN) you
 *            calculate the max. number of dits with the above formula.
 *            At SPEED_MIN you may only pause for 15 (6000 / 400) dits!
 *
 */
void pauseMorse(uint8_t len)
{
	if (len) {
		storeMsIndex2EncBuffer(len | 0x80);
	}
}

/**
 * Write a character to send into the Morse encoder ring buffer
 *
 * Input: ASCII code [0..255]
 *
 */
void writeMorseChar(uint8_t ch)
{static uint8_t sign_flag, chidx; uint8_t msidx;
 static char last_3ch[4];
	switch (ch) {
		case 32 :							// Space   [ASCII code 32]
		case 160 :							// NbSpace [ASCII code 160]
			if (sign_flag) {				// Space directly after a sign
				pauseMorse(4);				//  (length 4 dits)
				if (morseenc_status == MORSE_BUFFER_OK) {
					sign_flag = false;
				}
			}
			else {							// Pause for all other spaces
				pauseMorse(7);				//  (length 7 dits)
			}
			break;
		default :
			last_3ch[chidx] = ch; last_3ch[chidx + 1] = '\0';
			msidx = MsName2MsIndex(last_3ch);// Name in Morse table?
			if (morse_error) {
				chidx++;
				if (chidx > 2) {chidx = 0;}
				return;
			}
			storeMsIndex2EncBuffer(msidx);
			if (morseenc_status == MORSE_BUFFER_OK) {
				sign_flag = true;
			}
	}
	chidx = 0;
}

/**
 * Write a string to send into the Morse encoder ring buffer
 *
 * Input: String with ASCII text
 *
 */
void writeMorseString(char *str)
{
	while (*str) {
		writeMorseChar(*str++);
	}
}

/**
 * Get the number of indices still in the Morse encoder ring buffer
 *
 * Output: Number of indices (0: Buffer is empty!)
 *
 */
uint8_t getMorseEncBufferLength(void)
{int16_t enc_posdiff;
	enc_posdiff = enc_write_pos - enc_read_pos;
	if (enc_posdiff < 0) {
		enc_posdiff += (MORSEENC_BUFFER_MAXINDEX + 1);
	}
	return ((uint8_t) enc_posdiff);
}

/*****************************************************************************/
// Useful UART functions:

#ifndef DEBUG
/**
 * Send received Morse signs to the serial interface as ASCII text
 *
 */
void writeMorse(void)
{static uint8_t pos; uint8_t ch;
	ch = readMorseChar();
	if (ch) {
		writeChar(ch);
		pos++;
		if (pos >= LINE_LENGTH) {
			pos = 0;
			writeChar('\n');
		}
	}
}

#else

/**
 * Send decoder debug information to the serial interface
 *
 * Format: .0000 -0000 S000 D000  A:[X] B000
 *
 *   .    -> Dit length [0.1ms]
 *   -    -> Dah length [0.1ms]
 *   S    -> Decoder speed (should be (dit length / 10)!) [ms]
 *   D    -> Deviation (decoder speed - (dit length / 10)) [ms]
 *   A    -> The last received ASCII char
 *   B    -> Decoder buffer length (chars still in the buffer)
 *
 */
void writeDebugInfo(void)
{uint8_t ch;
	ch = readMorseChar();
	if (ch) {
		writeString_P(".");
		writeIntegerLength(ditlength, DEC, 4);
		writeString_P(" -");
		writeIntegerLength(dahlength, DEC, 4);
		writeString_P(" S");
		writeIntegerLength(decspeed, DEC, 3);
		writeString_P(" D");
		writeIntegerLength((decspeed - (ditlength / 10)), DEC, 3);
		writeString_P("  A:[");
		writeChar(ch);
		writeString_P("] B");
		writeIntegerLength(getMorseDecBufferLength(), DEC, 3);
		writeChar('\n');
	}
}
#endif

/******************************************************************************
 * Additional info
 * ****************************************************************************
 * Changelog:
 * - v. 3.3w 2012 by Dirk
 *
 * ****************************************************************************
 */

/*****************************************************************************/
// EOF

RP6 CONTROL M32

Header

/* ****************************************************************************
 *                           _______________________
 *                           \| RP6  ROBOT SYSTEM |/
 *                            \_-_-_-_-_-_-_-_-_-_/             >>> RP6 CONTROL
 * ----------------------------------------------------------------------------
 * ------------------------ [c]2012 - Dirk ------------------------------------
 * ****************************************************************************
 * File: RP6ControlMorseLib.h
 * Version: 3.4w
 * Target: RP6 CONTROL - ATMEGA32 @16.00MHz
 * Author(s): Dirk
 * ****************************************************************************
 * Description:
 * This is the RP6ControlMorse library header file.
 * You have to include this file, if you want to use the library
 * RP6ControlMorseLib.c in your own projects.
 *
 * ****************************************************************************
 * THE CHANGELOG CAN BE FOUND AT THE END OF THIS FILE!
 * ****************************************************************************
 */

#ifndef RP6CONTROLMORSE_H
#define RP6CONTROLMORSE_H

/*****************************************************************************/
// Includes:

#include "RP6ControlLib.h" 		// The RP6 Control Library. 
								// Always needs to be included!

/*****************************************************************************/
// Defines:

#define SPEED						100		// = 12 WpM = 60 CpM
// Calculate SPEED: SPEED = 1200 / WpM
//                  SPEED = 6000 / CpM
#define SPEED_MIN					400		// = 3 WpM = 15 CpM
#define SPEED_MAX					8		// = 150 WpM = 750 CpM
#define SPEED_VAR					5		// Decoder speed variation

#define LIMITED_PAUSE						// Decoder: Spaces limited
#define SPACE_CNT_LIMIT				3		// Max. number of spaces

//#define DEBUG								// Decoder debug mode

#define LIGHT								// Use LED1 to show Morse sign 

//#define SOUND								// Make Morse sign audible
#define Tone_D1						149		// 294Hz
#define Tone_Dis1					155		// 311Hz
#define Tone_E1						160		// 330Hz
#define Tone_F1						166		// 349Hz
#define Tone_Fis1					171		// 370Hz
#define Tone_G1						175		// 392Hz
#define Tone_Gis1					180		// 415Hz
#define Tone_A1						184		// 440Hz
#define Tone_Ais1					188		// 466Hz
#define Tone_H1						192		// 494Hz
#define Tone_C2						195		// 523Hz
#define Tone_Cis2					199		// 554Hz
#define Tone_D2						202		// 587Hz
#define Tone_Dis2					205		// 622Hz
#define Tone_E2						208		// 659Hz
#define Tone_F2						210		// 698Hz
#define Tone_Fis2					213		// 740Hz
#define Tone_G2						215		// 784Hz
#define Tone_Gis2					217		// 831Hz
#define Tone_A2						219		// 880Hz
#define Tone_Ais2					221		// 932Hz
#define Tone_H2						223		// 988Hz
#define Tone_Off					0

#define MS_SIGNALS_MAXINDEX			7
#define MS_SPECIALS_MAXINDEX		25
#define MORSESIGNS_MAXINDEX			79

// Flash constants (Morse tables):
const uint16_t ms_ft[MORSESIGNS_MAXINDEX + 1];
const uint8_t ms_a0uc_ft[MORSESIGNS_MAXINDEX + 1];
const uint8_t ms_a1uc_ft[MORSESIGNS_MAXINDEX + 1];
const uint8_t ms_a2uc_ft[MORSESIGNS_MAXINDEX + 1];
const uint8_t a_ms_ft[256];

#define MORSEDEC_BUFFER_MAXINDEX	31		// Morse decoder buffer length
#define MORSEENC_BUFFER_MAXINDEX	31		// Morse encoder buffer length

// Morse decoder/encoder status:
#define MORSE_BUFFER_OK				0
#define MORSE_BUFFER_OVERFLOW		1		// Morse buffer overflow

/*****************************************************************************/
// Variables:

extern uint8_t morsedec_status;
extern uint8_t morseenc_status;
extern uint8_t morse_error;
#ifdef SOUND
uint8_t tonepitch;
#endif

char morsedec_buffer[MORSEDEC_BUFFER_MAXINDEX + 2];
uint8_t dec_write_pos, dec_read_pos;
char morseenc_buffer[MORSEENC_BUFFER_MAXINDEX + 2];
uint8_t enc_write_pos, enc_read_pos;

uint16_t decspeed;
uint8_t speedvar;

uint16_t encspeed;

#ifdef DEBUG
uint16_t ditlength, dahlength;
#endif

/*****************************************************************************/
// Functions:

uint8_t Lower2UpperCase(uint8_t);
uint8_t Upper2LowerCase(uint8_t);

uint16_t MsIndex2MorseCode(uint8_t);
uint8_t MorseCode2MsIndex(uint16_t);
void MorseCode2MsName(char *, uint16_t);
uint8_t MsName2MsIndex(char *);

void MorseCode2MorseSign(char *, uint16_t);
uint16_t MorseSign2MorseCode(char *);

void clearMorseDecBuffer(void);
void initMorseDecoder(void);
void storeMsChar2DecBuffer(uint8_t);
void task_MorseDec(void);
uint8_t readMorseChar(void);
uint8_t readMorseChars(char *, uint8_t);
uint8_t getMorseDecBufferLength(void);

void initMorseEncoder(void);
uint8_t fetchMsIndexFromEncBuffer(void);
void task_MorseEnc(void);
void storeMsIndex2EncBuffer(uint8_t);
void pauseMorse(uint8_t);
void writeMorseChar(uint8_t);
void writeMorseString(char *);
uint8_t getMorseEncBufferLength(void);

#ifndef DEBUG
void writeMorseLCD(void);
#else
void showDebugInfoLCD(void);
#endif


#endif

/******************************************************************************
 * Additional info
 * ****************************************************************************
 * Changelog:
 * 
 *  ---> changes are documented in the file "RP6ControlMorseLib.c"
 *
 * ****************************************************************************
 */

/*****************************************************************************/
// EOF

Library

/* ****************************************************************************
 *                           _______________________
 *                           \| RP6  ROBOT SYSTEM |/
 *                            \_-_-_-_-_-_-_-_-_-_/             >>> RP6 CONTROL
 * ----------------------------------------------------------------------------
 * ------------------------ [c]2012 - Dirk ------------------------------------
 * ****************************************************************************
 * File: RP6ControlMorseLib.c
 * Version: 3.4w
 * Target: RP6 CONTROL - ATMEGA32 @16.00MHz
 *         with optional LC-Display 16x2 chars (CONRAD 190911-62)
 * Author(s): Dirk
 * ****************************************************************************
 * Description:
 *
 * The RP6 Control Morse Library.
 *
 * ****************************************************************************
 * ATTENTION: The 100us timer is used for the Morse decoder and encoder
 *            task! Please do not alter the variable "timer" elsewhere in
 *            your program!
 *
 * ****************************************************************************
 * THE CHANGELOG CAN BE FOUND AT THE END OF THIS FILE!
 * ****************************************************************************
 */
 
/*****************************************************************************/
// Includes:

#include "RP6ControlMorseLib.h"

/*****************************************************************************/
// Defines:

// RP6 Control Morse Decoder Connection (input):
//#define MORSEDEC_PORT	PORTC
//#define MORSEDEC_DDR	DDRC
//#define MORSEDEC_PIN	PINC
//#define MORSEDEC_IN		SCL					// PINC0  XBUS Pin 10
//#define MORSEDEC_IN		SDA					// PINC1  XBUS Pin 12

#define MORSEDEC_PORT	PORTD
#define MORSEDEC_DDR	DDRD
#define MORSEDEC_PIN	PIND
#define MORSEDEC_IN		EINT1				// PIND2  XBUS Pin 8

// RP6 Control Morse Encoder Connection (output):
#define MORSEENC_PORT	PORTC
#define MORSEENC_DDR	DDRC
#define MORSEENC_PIN	PINC
//#define MORSEENC_IN		SCL					// PINC0  XBUS Pin 10
#define MORSEENC_IN		SDA					// PINC1  XBUS Pin 12

//#define MORSEENC_PORT	PORTD
//#define MORSEENC_DDR	DDRD
//#define MORSEENC_PIN	PIND
//#define MORSEENC_IN		EINT1				// PIND2  XBUS Pin 8

// ----------------------------------------------------------------------------
// MORSE TABLES:

// Morse Table [0..79]:
// Morse decoders and encoders use this table for receiving or sending Morse
// code. This table consists of 16-bit constants. Each table index [0..79]
// (or each word constant) represents one Morse sign.
// The dots (dit) and the dashes (dah) are stored as two bits: The bits "01"
// stand for a dit and "11" for a dah, read from right to left in the binary
// notation. Between dits and dahs of a Morse sign you have to send a pause
// with the length of one dit. Between Morse signs there is a pause with the
// length of three dits (or one dah).
//
// Example:                     End <<<<7<<6<<5<<4<<3<<2<<1<<<< Start
//                                  ---DahDitDitDahDitDitDit
// 0x35D5 = 0b0011010111010101 -> 0b 00 11 01 01 11 01 01 01 -> $ (Dollar)
const uint16_t ms_ft[] PROGMEM =
// Signals (prosigns):
// Hex		  Binary		   Sign	   Index  Prosign
{0x5555, // 0b0101010101010101			 0		HH
 0x0DD5, // 0b0000110111010101					SK
 0x0377, // 0b0000001101110111					CT
 0x3757, // 0b0011011101010111					BK
 0x5D77, // 0b0101110101110111					CL
 0xDF77, // 0b1101111101110111			 5		CQ
 0x0FD7, // 0b0000111111010111					DO
 0x5FD5, // 0b0101111111010101			 7		SOS
//------------------------------------------------------
// Special characters:
// Hex		  Binary		   Sign	   Index  Prosign
 0x01DF, // 0b0000000111011111  ^G		 8
 0x00FF, // 0b0000000011111111  CH,^H
 0x01FD, // 0b0000000111111101  ^J		10
 0x15D5, // 0b0001010111010101  /S
 0x01D5, // 0b0000000111010101  ^S				VE
 0x075F, // 0b0000011101011111  /Z
 0x035F, // 0b0000001101011111  .Z
 0x037D, // 0b0000001101111101  /A,°A	15
 0x00DD, // 0b0000000011011101  Ä				AA
 0x0177, // 0b0000000101110111  C~
 0x035D, // 0b0000001101011101  \E
 0x0175, // 0b0000000101110101  /E
 0x01F5, // 0b0000000111110101  Eth		20
 0x03DF, // 0b0000001111011111  ~N
 0x007F, // 0b0000000001111111  Ö
 0x00F5, // 0b0000000011110101  Ü
 0x017D, // 0b0000000101111101  Thorn
 0x17D5, // 0b0001011111010101  ß		25
//------------------------------------------------------
// Normal characters:
// Hex		  Binary		   Sign	   Index  Prosign
 0x0F77, // 0b0000111101110111  !		26
 0x075D, // 0b0000011101011101  "
 0x35D5, // 0b0011010111010101  $
 0x015D, // 0b0000000101011101  &				AS
 0x07FD, // 0b0000011111111101  '		30
 0x01F7, // 0b0000000111110111  (				KN
 0x0DF7, // 0b0000110111110111  )
 0x01DD, // 0b0000000111011101  +				AR
 0x0F5F, // 0b0000111101011111  ,
 0x0D57, // 0b0000110101010111  -		35
 0x0DDD, // 0b0000110111011101  .
 0x01D7, // 0b0000000111010111  /				NR
 0x03FF, // 0b0000001111111111  0
 0x03FD, // 0b0000001111111101  1
 0x03F5, // 0b0000001111110101  2		40
 0x03D5, // 0b0000001111010101  3
 0x0355, // 0b0000001101010101  4
 0x0155, // 0b0000000101010101  5
 0x0157, // 0b0000000101010111  6
 0x015F, // 0b0000000101011111  7		45
 0x017F, // 0b0000000101111111  8
 0x01FF, // 0b0000000111111111  9
 0x057F, // 0b0000010101111111  :
 0x0777, // 0b0000011101110111  ;
 0x0357, // 0b0000001101010111  =		50		BT
 0x05F5, // 0b0000010111110101  ?				IMI
 0x077D, // 0b0000011101111101  @
 0x000D, // 0b0000000000001101  A
 0x0057, // 0b0000000001010111  B				DE
 0x0077, // 0b0000000001110111  C		55
 0x0017, // 0b0000000000010111  D
 0x0001, // 0b0000000000000001  E
 0x0075, // 0b0000000001110101  F
 0x001F, // 0b0000000000011111  G
 0x0055, // 0b0000000001010101  H		60
 0x0005, // 0b0000000000000101  I
 0x00FD, // 0b0000000011111101  J
 0x0037, // 0b0000000000110111  K				K
 0x005D, // 0b0000000001011101  L
 0x000F, // 0b0000000000001111  M		65
 0x0007, // 0b0000000000000111  N
 0x003F, // 0b0000000000111111  O
 0x007D, // 0b0000000001111101  P
 0x00DF, // 0b0000000011011111  Q
 0x001D, // 0b0000000000011101  R		70		R
 0x0015, // 0b0000000000010101  S
 0x0003, // 0b0000000000000011  T
 0x0035, // 0b0000000000110101  U
 0x00D5, // 0b0000000011010101  V
 0x003D, // 0b0000000000111101  W		75
 0x00D7, // 0b0000000011010111  X
 0x00F7, // 0b0000000011110111  Y
 0x005F, // 0b0000000001011111  Z
 0x0DF5};// 0b0000110111110101  _		79
// Remarks: - SOS (Morse sign ...---...) can not be stored in a 16-bit
//            constant because SOS is the only Morse sign with 9 dits/dahs.
//            So SOS is stored as the (not existing) Morse sign ...---..
//            (SOI) and must be treated special in decoders/encoders.  


// Morse-ASCII-Table [0..79]:
// Morse decoders use this table for receiving Morse code.
const uint8_t ms_a0uc_ft[] PROGMEM = 
//H   S   C   B    C   C   D   S
{104,115, 99, 98, 99, 99,100,115,
//0                    5
//^   C   ^   %    ^   %   *   /A  Ä   C~  \E  /E  Et  ~N   Ö   Ü  To   ß
  94, 99, 94, 37, 94, 37, 42,193,196,199,200,201,208,209,214,220,222,223,
//        10                   15                  20                   25
//!  "  $  &  '  (  )   +  ,  -  .  /  0  1  2   3  4  5  6  7  8  9  :  ;
 33,34,36,38,39,40,41,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,
//            30             35              40             45
//=  ?  @  A  B  C   D   E    F   G   H   I   J   K   L   M   N   O    P   Q
 61,63,64,65,66,67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, 81,
//50            55                   60                   65
// R  S   T   U   V   W   X   Y    Z   _  
  82, 83, 84, 85, 86, 87, 88, 89, 90,95};		// Et = Eth,  To = Thorn
//70                  75              79

const uint8_t ms_a1uc_ft[] PROGMEM = 
//H   K   T   K    L   Q   O   O
{104,107,116,107,108,113,111,111,
//0                    5
//G   H   J   S    S   Z   Z
 103,104,106,115,115,122,122, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//        10                   15                  20                   25
 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,
//            30             35              40             45
 32,32,32,32,32,32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//50            55                   60                   65
  32, 32, 32, 32, 32, 32, 32, 32, 32,32};		// Et = Eth,  To = Thorn
//70                  75              79

const uint8_t ms_a2uc_ft[] PROGMEM = 
//                             S
{ 32, 32, 32, 32, 32, 32, 32,115,
// 0                   5
  32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//        10                   15                  20                   25
 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,
//            30             35              40             45
 32,32,32,32,32,32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//50            55                   60                   65
  32, 32, 32, 32, 32, 32, 32, 32, 32,32};		// Et = Eth,  To = Thorn
//70                  75              79
// Prosigns and special characters are stored as lower case letters (hh,
// sk, ^g, ch ...) in this table.
// Remarks: - The special chars  ^G, ^J, /S, ^S, /Z, .Z [indices 8, 10..14]
//            are represented as ^g, ^j, %s, ^s, %z, *z in this table.
//          - If Morse decoders receive a pause with the length of 7 dits,
//            they have to give out the ASCII code ' ' (space [32]).


// ASCII-Morse-Table [0..255]:
// Morse encoders use this table to send Morse code.
const uint8_t a_ms_ft[] PROGMEM =
{51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//0              5              10              15             20
 51,51,51,51,51,51,51,51,
//24                30
//_  !  "  ?  $  ?  &  '  (  )   X  +  ,  -  .  /  0  1   2  3  4  5  6  7
 79,26,27,51,28,51,29,30,31,32,76,33,34,35,36,37,38,39,40,41,42,43,44,45,
//32       35             40              45             50              55
//8  9  :  ;  ?  =  ?  ?   @  A  B  C  D  E  F  G  H   I  J  K  L  M  N  O
 46,47,48,49,51,50,51,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,
//56          60             65              70              75
//P  Q  R  S  T  U  V  W  X   Y  Z  [  ?  ]  ?  _   ?  A  B  C  D  E  F  G
 68,69,70,71,72,73,74,75,76,77,78,31,51,32,51,79,51,53,54,55,56,57,58,59,
//80             85             90              95             100
//H  I  J  K  L  M  N  O   P  Q  R  S  T  U  V  W   X  Y  Z  {  ?  }  ?  ?
 60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,31,51,32,51,51,
//104              110             115            120             125
//?  ?  ?  ?  ?  ?  ?  ?   ?  ?  ?  ?  ?  ?  ?  ?  ?   ?  ?  ?  ?  ?  ?  ?
 51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//128  130            135             140            145             150
//?  ?  ?  ?  ?  ?  ?  ?   _  ?  ?  ?  ?  ?  ?  ?  ?   ?  ?  ?  ?  ?  ?  ?
 51,51,51,51,51,51,51,51,79,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//152     155            160             165             170            175
//?  ?  ?  ?  ?  ?  ?  ?  ?   ?  ?  ?  ?  ?  ?  ?  ?  /A  ?  ?  Ä  ?  ?  C~
 51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,15,51,51,16,51,51,17,
//176        180             185            190             195
//\E/E  ?  ?  ?  ?  ?  ?  Et ~N  ?  ?  ?  ?  Ö  X   ?  ?  ?  ?  Ü  ?  To ß
 18,19,51,51,51,51,51,51,20,21,51,51,51,51,22,76,51,51,51,51,23,51,24,25,
//200           205             210            215             220
//? /A  ?  ?  Ä  ?  ?  C~ \E /E  ?  ?  ?  ?  ?  ?  Et ~N  ?  ?  ?  ?  Ö  /
 51,15,51,51,16,51,51,17,18,19,51,51,51,51,51,51,20,21,51,51,51,51,22,37,
//224              230             235            240             245
//?  ?  ?  ?  Ü  ?  To ?
 51,51,51,51,23,51,24,51};					// Et = Eth,  To = Thorn
//248                 255
// Remarks: - ASCII codes 91 '[' and 123 '{' are converted to Morse
//            code '(' [31].
//          - ASCII codes 93 ']' and 125 '}' are converted to Morse
//            code ')' [32].
//          - ASCII code 215 (multiplication sign) is converted to
//            Morse code 'X' [76].
//          - ASCII code 247 (division sign) is converted to Morse
//            code '/' [37].
//          - ASCII codes 32 (sp) and 160 (nbsp) are represented as
//            '_' [79] in this table but must be treated special in
//            encoders: The Morse encoder has to send a pause with
//            the length of 7 dits for a space.
//          - All non printable ASCII codes [0..31] and other codes
//            not defined in the Morse code are converted to Morse
//            code '?' [51].

// MORSE TABLES (END)
// ----------------------------------------------------------------------------

/*****************************************************************************/
// Variables:

uint8_t morsedec_status;
uint8_t morseenc_status;
uint8_t morse_error;

/*****************************************************************************/
// Functions:

/**
 * Convert lower case to upper case letters
 *
 * Input:  ASCII code [0..255]
 * Output: ASCII code, only with upper case letters
 *
 */
uint8_t Lower2UpperCase(uint8_t ch)
{uint8_t chuc;
	chuc = ch;
	if ((ch >= 97) && (ch <= 122)) {
		chuc -= 32;
	}
	if ((ch >= 224) && (ch <= 254) && (ch != 247)) {
		chuc -= 32;
	}
	return (chuc);
}

/**
 * Convert upper case to lower case letters
 *
 * Input:  ASCII code [0..255]
 * Output: ASCII code, only with lower case letters
 *
 */
uint8_t Upper2LowerCase(uint8_t ch)
{uint8_t chlc;
	chlc = ch;
	if ((ch >= 65) && (ch <= 90)) {
		chlc += 32;
	}
	if ((ch >= 192) && (ch <= 222) && (ch != 215)) {
		chlc += 32;
	}
	return (chlc);
}

/**
 * Output the Morse code of a Morse table index
 *
 * Input:  Morse table index [0..MORSESIGNS_MAXINDEX]
 * Output: Morse code (See table ms_ft[] above!)
 *
 */
uint16_t MsIndex2MorseCode(uint8_t msindex)
{
	morse_error = false;
	return (pgm_read_word(&ms_ft[msindex]));
}

/**
 * Output the table index of a Morse code
 *
 * Input:  Morse code (See table ms_ft[] above!)
 * Output: Morse table index [0..MORSESIGNS_MAXINDEX]
 *
 */
uint8_t MorseCode2MsIndex(uint16_t morsecode)
{uint8_t msidx;
	for (msidx = 0; msidx <= MORSESIGNS_MAXINDEX; msidx++) {
		if (morsecode == pgm_read_word(&ms_ft[msidx])) {break;}
	}
	if (msidx <= MORSESIGNS_MAXINDEX) {
		morse_error = false;
		return (msidx);					// Morse table index
	}
	else {
		morse_error = true;				// Unknown Morse code:
		return (51);					//  Return table index of '?'
	}
}

/**
 * Output the Morse sign name of a Morse code
 *
 * Input:  Morse code (See table ms_ft[] above!)
 * Output: String with Morse sign name (1..3 ASCII letters)
 *
 */
void MorseCode2MsName(char *msname, uint16_t morsecode)
{uint8_t msidx;
	msidx = MorseCode2MsIndex(morsecode);
	msname[0] = pgm_read_byte(&ms_a0uc_ft[msidx]);
	msname[1] = pgm_read_byte(&ms_a1uc_ft[msidx]);
	if (msname[1] == 32) {msname[1] = '\0';}
	msname[2] = pgm_read_byte(&ms_a2uc_ft[msidx]);
	if (msname[2] == 32) {
		msname[2] = '\0';
	}
	else {
		msname[3] = '\0';
	}
}

/**
 * Output the Morse table index of a Morse sign name
 *
 * Input:  String with Morse sign name (1..3 ASCII letters)
 * Output: Morse table index [0..MORSESIGNS_MAXINDEX]
 *
 */
uint8_t MsName2MsIndex(char *msname)
{uint8_t msidx;
	for (msidx = 0; msidx <= MORSESIGNS_MAXINDEX; msidx++) {
		if (msname[0] == pgm_read_byte(&ms_a0uc_ft[msidx])) {
			if ((pgm_read_byte(&ms_a1uc_ft[msidx]) == 32)
			 || (msname[1] == pgm_read_byte(&ms_a1uc_ft[msidx]))) {
				if ((pgm_read_byte(&ms_a2uc_ft[msidx]) == 32)
				 || (msname[2] == pgm_read_byte(&ms_a2uc_ft[msidx]))) {
					break;
				}
			}
		}
	}
	if (msidx <= MORSESIGNS_MAXINDEX) {
		morse_error = false;
		return (msidx);					// Morse table index
	}
	else {
		morse_error = true;				// Unknown Morse sign name:
		return (51);					//  Return table index of '?'
	}
}

/**
 * Output the Morse sign of a Morse code
 *
 * Input:  Morse code (See table ms_ft[] above!)
 * Output: String with the Morse sign (1..9 dits [.] or dahs [-])
 *
 * Example: $  -> 0b0011010111010101  -> Morse sign ...-..-
 *
 */
void MorseCode2MorseSign(char *morsesign, uint16_t morsecode)
{uint8_t i; uint16_t ms_code;
	ms_code = morsecode;
	i = 0;
	do {
		switch (ms_code & 3) {
			case 1 :					// dit!
				morsesign[i] = '.';
				i++; break;
			case 3 :					// dah!
				morsesign[i] = '-';
				i++;
		}
		ms_code >>= 2;
	} while (ms_code);
	if (morsecode == 0x5FD5) {			// SOS: Add last dit!
		morsesign[i] = '.';
		i++;
	}
	morsesign[i] = '\0';
	morse_error = false;
}

/**
 * Output the Morse code of a Morse sign
 *
 * Input:  String with the Morse sign (1..9 dits [.] or dahs [-])
 * Output: Morse code (See table ms_ft[] above!)
 *
 * Example: $  -> Morse sign ...-..-  -> 0b0011010111010101
 *
 */
uint16_t MorseSign2MorseCode(char *morsesign)
{uint8_t i, ch; uint16_t ms_code;
	ms_code = 0;
	ch = 1;
	for (i = 0; i <= 7; i++) {
		ms_code >>= 2;
		if (ch) {
			ch = morsesign[i];
			switch (ch) {
				case '.' :					// dit!
					ms_code |= 0x4000; break;
				case '-' :					// dah!
					ms_code |= 0xC000;
			}
		}
		
	}
	if ((ms_code == 0x5FD5) && (morsesign[8] != '.')) {
		ms_code = 0x05F5;	// SOS: If last dit doesn't exist, return '?'!
		morse_error = true;
	}
	else {
		morse_error = false;
	}
	return (ms_code);
}

/*****************************************************************************/
// Morse decoder functions:

/**
 * Clear the Morse decoder ring buffer
 *
 */
void clearMorseDecBuffer(void)
{
	morsedec_status = MORSE_BUFFER_OK;		// Decoder buffer status ok
	dec_write_pos = 255;					// Reset buffer write position
	dec_read_pos = 255;						// Reset buffer read position
}

/**
 * Init Morse Decoder
 *
 * Call this once before using the Morse decoder (receiver) task!
 *
 */
void initMorseDecoder(void)
{
	MORSEDEC_DDR &= ~MORSEDEC_IN;			// Decoder input pin
	MORSEDEC_PORT |= MORSEDEC_IN;			// MORSEDEC_IN -> Pullup
	morse_error = false;					// Reset Morse error flag
	clearMorseDecBuffer();					// Clear the decoder buffer
	decspeed = SPEED;						// Decoder speed
	speedvar = SPEED_VAR;					// Decoder speed variation
#ifdef SOUND
	tonepitch = Tone_C2;					// Set tone pitch
#endif
}

/**
 * Store a decoded (prosign) Morse sign char into the decoder ring buffer
 *
 * Input: ASCII char (part of a string with the (pro)sign name)
 *
 */
void storeMsChar2DecBuffer(uint8_t ch)
{
	if (getMorseDecBufferLength() < MORSEDEC_BUFFER_MAXINDEX) {
		dec_write_pos++;
		if (dec_write_pos > MORSEDEC_BUFFER_MAXINDEX) {
			dec_write_pos = 0;
		}
		morsedec_buffer[dec_write_pos] = ch;
		morsedec_status = MORSE_BUFFER_OK;	// Decoder buffer status ok
	}
	else {
		morsedec_status = MORSE_BUFFER_OVERFLOW;// Decoder buffer overflow
	}
}

/**
 * Morse decoder task
 *
 */
void task_MorseDec(void)
{uint16_t time_100usecs;
 static char ms_sign[10]; uint8_t temp;
 static uint16_t last_timer, signal, pause;
 static uint8_t ditdah, ditdah_cnt;
 char ms_name[4]; 
#ifdef SOUND
 static uint8_t tone_off;
#endif
#ifdef LIMITED_PAUSE
 static uint8_t space_cnt;
#endif 
	time_100usecs = timer - last_timer;
	last_timer += time_100usecs;
	temp = MORSEDEC_PIN & MORSEDEC_IN;		// Read Morse level
	if (temp) {								// Signal on
#ifdef SOUND
		if (tone_off) {
			setBeeperPitch(tonepitch);
			tone_off = false;
		}
#endif
#ifdef LIGHT
		externalPort.LED1 = true;
		outputExt();
#endif
		signal += time_100usecs;
		if (pause > (decspeed * 20)) {		// Pause > 2 dits:
			if (ditdah) {					//  Morse sign end (length 3 dits)
				ms_sign[ditdah_cnt] = ditdah;
				ditdah_cnt++;
				ms_sign[ditdah_cnt] = '\0';
				ditdah_cnt = 0;
				ditdah = 0;
				MorseCode2MsName(ms_name, MorseSign2MorseCode(ms_sign));
				temp = 0;
				while (ms_name[temp]) {
					storeMsChar2DecBuffer(ms_name[temp++]);
				}
			}
			pause = 0;
		}
		if (pause) {						// Short pause: 
			if (ditdah) {					//  Dit or dah end (length 1 dit)
				ms_sign[ditdah_cnt] = ditdah;
				ditdah_cnt++;
				ms_sign[ditdah_cnt] = '\0';
				if (ditdah_cnt > 8) {ditdah_cnt = 0;}
				ditdah = 0;
			}
			pause = 0;
		}
	}
	else {									// Signal off (pause)
#ifdef SOUND
		setBeeperPitch(Tone_Off);
		tone_off = true;
#endif
#ifdef LIGHT
		externalPort.LED1 = false;
		outputExt();
#endif
		pause += time_100usecs;
		if (pause > (decspeed * 50)) {		// Pause > 5 dits:
			if (ditdah) {					//  Space or longer pause
				ms_sign[ditdah_cnt] = ditdah;
				ditdah_cnt++;
				ms_sign[ditdah_cnt] = '\0';
				ditdah_cnt = 0;
				ditdah = 0;
				MorseCode2MsName(ms_name, MorseSign2MorseCode(ms_sign));
				temp = 0;
				while (ms_name[temp]) {
					storeMsChar2DecBuffer(ms_name[temp++]);
				}
#ifdef LIMITED_PAUSE
				space_cnt = SPACE_CNT_LIMIT;
				space_cnt--;
#endif
				storeMsChar2DecBuffer(' ');		// Add a space after a sign
				pause = 0;
			}
#ifdef LIMITED_PAUSE
			if (space_cnt) {
#endif
				if (pause >= (decspeed * 70)) {// Pause >= 7 dits:
					storeMsChar2DecBuffer(' '); // Add spaces while pause
					pause -= (decspeed * 70);
#ifdef LIMITED_PAUSE
					space_cnt--;
#endif
				}
#ifdef LIMITED_PAUSE
			}
			else {
				pause = 0;
			}
#endif
		}
		if (signal > (decspeed * 20)) {	// Signal > 2 dits:
#ifdef DEBUG
			dahlength = signal;
#endif
			ditdah = '-';					//  Dah (length 3 dits)!
			if (signal >= (decspeed * 33)) {// Signal >= 3.3 dits (+10%):
				decspeed += speedvar;		//   Reduce decoder speed
				if (decspeed > SPEED_MIN) {decspeed = SPEED_MIN;}
			}
			signal = 0;
		}
		if (signal) {						// Short signal:
#ifdef DEBUG
			ditlength = signal;
#endif
			ditdah = '.';					//  Dit!
			if (signal <= (decspeed * 9)) {// Signal <= 0.9 dits (-10%):
				decspeed -= speedvar;		//  Increase decoder speed
				if (decspeed < SPEED_MAX) {decspeed = SPEED_MAX;}
			}
			signal = 0;
		}
	}
}

/**
 * Read next character from the Morse decoder ring buffer
 *
 * Output: Printable ASCII character [32..255] (as part of
 *         a received/decoded (prosign) Morse sign name)
 *         OR 0 (false), if the ring buffer is empty
 *
 */
uint8_t readMorseChar(void)
{uint8_t ch;
	if (dec_read_pos != dec_write_pos) {
		dec_read_pos++;
		if (dec_read_pos > MORSEDEC_BUFFER_MAXINDEX) {
			dec_read_pos = 0;
		}
		ch = morsedec_buffer[dec_read_pos];
	}
	else {
		ch = 0;
	}
	return (ch);
}

/**
 * Read next [numberOfChars] characters from the Morse decoder ring buffer
 *
 * Output: Number of characters copied to *buf,
 *         string *buf with the copied characters
 *
 */
uint8_t readMorseChars(char *buf, uint8_t numberOfChars)
{uint8_t ch, i;
	i = 0;
	while (i < numberOfChars) {
		ch = readMorseChar();
		if (ch) {
			buf[i] = ch;
		}
		else {break;}
		i++;
	}
	buf[i] = '\0';
	return (i);
}

/**
 * Get the number of characters still in the Morse decoder ring buffer
 *
 * Output: Number of characters (0: Buffer is empty!)
 *
 */
uint8_t getMorseDecBufferLength(void)
{int16_t dec_posdiff;
	dec_posdiff = dec_write_pos - dec_read_pos;
	if (dec_posdiff < 0) {
		dec_posdiff += (MORSEDEC_BUFFER_MAXINDEX + 1);
	}
	return ((uint8_t) dec_posdiff);
}

/*****************************************************************************/
// Morse encoder functions:

/**
 * Init Morse Encoder
 *
 * Call this once before using the Morse encoder (sender) task!
 *
 */
void initMorseEncoder(void)
{
	MORSEENC_DDR |= MORSEENC_IN;			// Encoder output pin
	MORSEENC_PORT &= ~MORSEENC_IN;			// Output low
	morse_error = false;					// Reset Morse error flag
	morseenc_status = MORSE_BUFFER_OK;		// Encoder buffer status ok
	enc_write_pos = 255;					// Reset buffer write pointer
	enc_read_pos = 255;						// Reset buffer read pointer
	encspeed = SPEED;						// Set encoder speed
#ifdef SOUND
	tonepitch = Tone_C2;					// Set tone pitch
#endif
}

/**
 * Fetch next Morse table index from the Morse encoder ring buffer
 *
 * Output: Morse table index [0..MORSESIGNS_MAXINDEX(..127)]
 *         OR pause length [129..255] (pause 1..127 dits)
 *         OR 128 (0x80), if the ring buffer is empty
 *
 */
uint8_t fetchMsIndexFromEncBuffer(void)
{uint8_t msidx;
	if (enc_read_pos != enc_write_pos) {
		enc_read_pos++;
		if (enc_read_pos > MORSEENC_BUFFER_MAXINDEX) {
			enc_read_pos = 0;
		}
		msidx = morseenc_buffer[enc_read_pos];
	}
	else {
		msidx = 0x80;
	}
	return (msidx);
}

/**
 * Morse encoder task
 *
 */
void task_MorseEnc(void)
{static uint8_t busy_flag, signal_flag, pause_flag, sos_flag, pause_dits;
 static uint16_t last_timer, ms_code; uint8_t msidx;
	if (busy_flag) {						// Encoder busy!
		if (signal_flag) {					// Sending signal
			if (!pause_flag) {				// Waiting for signal end
				if ((timer - last_timer)
				 >= (encspeed * 10 * (ms_code & 3))) {
#ifdef SOUND
					setBeeperPitch(Tone_Off);
#endif
#ifdef LIGHT
					externalPort.LED1 = false;
					outputExt();
#endif
					MORSEENC_PORT &= ~MORSEENC_IN;
					last_timer = timer;
					pause_flag = true;
					ms_code >>= 2;
				}
			}
			else {							// Pause after a signal
				if (ms_code) {				// Dit/dah (signal) end:
					if ((timer - last_timer) >= (encspeed * 10)) {
						signal_flag = false;//  Pause 1 dit
					}
				}
				else {						// Morse sign end:
					if (sos_flag) {			//  Case SOS:
						ms_code = 0x0001;	//   Add last dit
						sos_flag = false;
					}
					else {					//  Case sign end:
						if ((timer - last_timer) >= (encspeed * 30)) {
							busy_flag = false;// Pause 3 dits
						}
					}
				}
			}
		}
		else {								// Signal end
			if (pause_dits) {				// Make a longer pause
				if ((timer - last_timer) >= (encspeed * 10 * pause_dits)) {
					busy_flag = false;		// Longer pause end
				}
			}
			else {							// Start new signal (dit/dah)
#ifdef SOUND
				setBeeperPitch(tonepitch);
#endif
#ifdef LIGHT
				externalPort.LED1 = true;
				outputExt();
#endif
				MORSEENC_PORT |= MORSEENC_IN; 
				last_timer = timer;
				pause_flag = false;
				signal_flag = true;
			}
		}
	}
	else {									// Encoder not busy!
		msidx = fetchMsIndexFromEncBuffer();// Get next index to send
		if (msidx == 0x80) {				//  from the ring buffer
			return;							// Buffer empty: Return
		}
		else {
			if (msidx < 0x80) {				// Morse sign to send
				ms_code = MsIndex2MorseCode(msidx);
				if (ms_code == 0x5FD5) {
					sos_flag = true;		// Sign is SOS
				}
				else {
					sos_flag = false;
				}
				pause_dits = 0;
			}
			else {							// (msidx > 0x80): Longer pause
				last_timer = timer;
				pause_dits = msidx - 0x80;
			}
			signal_flag = false;
			busy_flag = true;				// Sign / longer pause can be sent
		}
	}
}

/**
 * Store a Morse table index into the Morse encoder ring buffer
 *
 * Input: Morse table index [0..MORSESIGNS_MAXINDEX(..127)]
 *        OR pause length [129..255] (pause 1..127 dits)
 *
 */
void storeMsIndex2EncBuffer(uint8_t msindex)
{
	if (getMorseEncBufferLength() < MORSEENC_BUFFER_MAXINDEX) {
		enc_write_pos++;
		if (enc_write_pos > MORSEENC_BUFFER_MAXINDEX) {
			enc_write_pos = 0;
		}
		morseenc_buffer[enc_write_pos] = msindex;
		morseenc_status = MORSE_BUFFER_OK;	// Encoder buffer status ok
	}
	else {
		morseenc_status = MORSE_BUFFER_OVERFLOW; // Encoder buffer overflow
	}
}

/**
 * Write a pause length to send into the Morse encoder ring buffer
 *
 * Input: Pause length [1..127 dits] (0.14..18.14 spaces)
 *
 * With this function you can reach longer pauses.
 *   Examples:
 *   pauseMorse(7);  is identical with  writeMorseChar(' ');
 *   pauseMorse(14); is identical with  writeMorseString("  ");
 * The function pauseMorse(len) only writes one byte into the encoder ring
 * buffer for a longer pause, while writeMorseChar(' ') writes one byte for
 * each space to send. You should use writeMorseChar(' ') for single spaces
 * (between words) and pauseMorse(len) for longer pauses.
 *
 * ATTENTION: !-----------------------------------------------------------!
 *            ! The max. pause length you can reach with this function is !
 *            ! about 6 seconds! So the max. input value of this function !
 *            ! depends on encspeed!!!                                    !
 *            !-----------------------------------------------------------!
 *            !   ==>  Max. pause length [dits] = 6000 / encspeed  <==    !
 *            !-----------------------------------------------------------!
 *            For encspeeds from 8 (SPEED_MAX) to 47 the max. pause length
 *            is 127 dits. For encspeeds from 48 to 400 (SPEED_MIN) you
 *            calculate the max. number of dits with the above formula.
 *            At SPEED_MIN you may only pause for 15 (6000 / 400) dits!
 *
 */
void pauseMorse(uint8_t len)
{
	if (len) {
		storeMsIndex2EncBuffer(len | 0x80);
	}
}

/**
 * Write a character to send into the Morse encoder ring buffer
 *
 * Input: ASCII code [0..255]
 *
 */
void writeMorseChar(uint8_t ch)
{static uint8_t sign_flag, chidx; uint8_t msidx;
 static char last_3ch[4];
	switch (ch) {
		case 32 :							// Space   [ASCII code 32]
		case 160 :							// NbSpace [ASCII code 160]
			if (sign_flag) {				// Space directly after a sign
				pauseMorse(4);				//  (length 4 dits)
				if (morseenc_status == MORSE_BUFFER_OK) {
					sign_flag = false;
				}
			}
			else {							// Pause for all other spaces
				pauseMorse(7);				//  (length 7 dits)
			}
			break;
		default :
			last_3ch[chidx] = ch; last_3ch[chidx + 1] = '\0';
			msidx = MsName2MsIndex(last_3ch);// Name in Morse table?
			if (morse_error) {
				chidx++;
				if (chidx > 2) {chidx = 0;}
				return;
			}
			storeMsIndex2EncBuffer(msidx);
			if (morseenc_status == MORSE_BUFFER_OK) {
				sign_flag = true;
			}
	}
	chidx = 0;
}

/**
 * Write a string to send into the Morse encoder ring buffer
 *
 * Input: String with ASCII text
 *
 */
void writeMorseString(char *str)
{
	while (*str) {
		writeMorseChar(*str++);
	}
}

/**
 * Get the number of indices still in the Morse encoder ring buffer
 *
 * Output: Number of indices (0: Buffer is empty!)
 *
 */
uint8_t getMorseEncBufferLength(void)
{int16_t enc_posdiff;
	enc_posdiff = enc_write_pos - enc_read_pos;
	if (enc_posdiff < 0) {
		enc_posdiff += (MORSEENC_BUFFER_MAXINDEX + 1);
	}
	return ((uint8_t) enc_posdiff);
}

/*****************************************************************************/
// Useful LCD functions:

#ifndef DEBUG
/**
 * Show received Morse signs on the LCD 16x2 chars as ASCII text
 *
 */
void writeMorseLCD(void)
{static uint8_t pos; static char line2[17]; uint8_t ch;
	ch = readMorseChar();
	if (ch) {
		writeCharLCD(ch);
		line2[pos] = ch;
		pos++;
		if (pos >= 16) {
			pos = 0;
			clearLCD();
			writeStringLCD(line2);			// Copy line 2 to line 1
			setCursorPosLCD(1, 0);			// line 2, pos 1
		}
	}
}

#else

/**
 * Show decoder debug information on the LCD
 *
 * Format: .0000 -0000 S000
 *         B000 A[XXX] D000
 *
 *   .    -> Dit length [0.1ms]
 *   -    -> Dah length [0.1ms]
 *   S    -> Decoder speed (should be (dit length / 10)!) [ms]
 *   B    -> Decoder buffer length (chars still in the buffer)
 *   A    -> The 3 last received ASCII chars
 *   D    -> Deviation (decoder speed - (dit length / 10)) [ms]
 *
 */
void showDebugInfoLCD(void)
{static char last_3ch[4]; uint8_t ch;
	ch = readMorseChar();
	if (ch) {
		last_3ch[0] = last_3ch[1]; last_3ch[1] = last_3ch[2];
		last_3ch[2] = ch; last_3ch[3] = '\0';
		setCursorPosLCD(0, 0);				// line 1, pos 1
		writeStringLCD_P(".");
		writeIntegerLengthLCD(ditlength, DEC, 4);
		writeStringLCD_P(" -");
		writeIntegerLengthLCD(dahlength, DEC, 4);
		writeStringLCD_P(" S");
		writeIntegerLengthLCD(decspeed, DEC, 3);
		setCursorPosLCD(1, 0);				// line 2, pos 1
		writeStringLCD_P("B");
		writeIntegerLengthLCD(getMorseDecBufferLength(), DEC, 3);
		writeStringLCD_P(" A[");
		writeStringLCD(last_3ch);
		writeStringLCD_P("] D");
		writeIntegerLengthLCD((decspeed - (ditlength / 10)), DEC, 3);
	}
}
#endif

/******************************************************************************
 * Additional info
 * ****************************************************************************
 * Changelog:
 * - v. 3.4w 2012 by Dirk
 *
 * ****************************************************************************
 */

/*****************************************************************************/
// EOF

RP6 CCPRO M128

/* ****************************************************************************
 *                           _______________________
 *                           \| RP6  ROBOT SYSTEM |/
 *                            \_-_-_-_-_-_-_-_-_-_/              >>> CCPRO M128
 * ----------------------------------------------------------------------------
 * ----------------------- [c]2012 - Dirk -------------------------------------
 * ****************************************************************************
 * File: RP6MorseCClib.cc
 * Version: 1.3w - CompactC
 * Target: RP6 CCPRO M128 - C-Control PRO M128 @14.7456MHz
 *         mit optionalem LC-Display 16x2 Zeichen (CONRAD 190911)
 *         [oder OLED Textdisplay 16x2 Zeichen (CONRAD 197622)]
 *         [oder Backlight Display 16x2 Zeichen (CONRAD 191621)]
 * Author(s): Dirk
 * ****************************************************************************
 * Beschreibung:
 * Dies ist meine RP6 CCPRO M128 Morse Bibliothek
 *
 * ****************************************************************************
 * Mit den Funktionen in dieser Bibliothek kann der RP6 mit CCPRO M128
 * Morse Zeichen senden und empfangen.
 *
 * ****************************************************************************
 * CHANGELOG FINDEN SIE AM ENDE DIESER DATEI!
 * ****************************************************************************
 */

 // Alles nur EINMAL einbinden!
#ifndef __RP6MORSECCLIB__
#define __RP6MORSECCLIB__


/******************************************************************************/
// Defines:

// RP6 CCPRO M128 Morse-Decoder Anschluß (Eingang):
//#define MORSEDEC_IN 24          // PortD.0 (RP6: SCL)
#define MORSEDEC_IN 25          // PortD.1 (RP6: SDA)
//#define MORSEDEC_IN 37          // PortE.5 (RP6: INT1)

// RP6 CCPRO M128 Morse-Encoder Anschluß (Ausgang):
#define MORSEENC_IN 37          // PortE.5 (RP6: INT1)

#define SPEED                       100 // = 12 WpM = 60 CpM
// Berechne SPEED: SPEED = 1200 / WpM
//                 SPEED = 6000 / CpM
#define SPEED_MIN                   400 // = 3 WpM = 15 CpM
#define SPEED_MAX                   8   // = 150 WpM = 750 CpM
#define SPEED_VAR                   5   // Decoder Speed Variation

#define LIMITED_PAUSE                   // Decoder: Leerzeichen begrenzt
#define SPACE_CNT_LIMIT             3   // Max. Anzahl Leerzeichen

//#define DEBUG                           // Decoder Debug Modus

#define LIGHT                           // LED1 zeigt die Morse Zeichen

//#define SOUND                           // Macht die Morse Zeichen hörbar
#define Tone_D1                     392 //294Hz
#define Tone_Dis1                   370 //311Hz
#define Tone_E1                     349 //330Hz
#define Tone_F1                     330 //349Hz
#define Tone_Fis1                   311 //370Hz
#define Tone_G1                     294 //392Hz
#define Tone_Gis1                   277 //415Hz
#define Tone_A1                     262 //440Hz
#define Tone_Ais1                   247 //466Hz
#define Tone_H1                     233 //494Hz
#define Tone_C2                     220 //523Hz
#define Tone_Cis2                   208 //554Hz
#define Tone_D2                     196 //587Hz
#define Tone_Dis2                   185 //622Hz
#define Tone_E2                     175 //659Hz
#define Tone_F2                     165 //698Hz
#define Tone_Fis2                   156 //740Hz
#define Tone_G2                     147 //784Hz
#define Tone_Gis2                   139 //831Hz
#define Tone_A2                     131 //880Hz
#define Tone_Ais2                   124 //932Hz
#define Tone_H2                     117 //988Hz

#define MS_SIGNALS_MAXINDEX         7
#define MS_SPECIALS_MAXINDEX        25
#define MORSESIGNS_MAXINDEX         79

#define MORSEDEC_BUFFER_MAXINDEX    31  // Morse Decoder Puffer Länge
#define MORSEENC_BUFFER_MAXINDEX    31  // Morse Encoder Puffer Länge

// Morse Decoder/Encoder Status:
#define MORSE_BUFFER_OK             0
#define MORSE_BUFFER_OVERFLOW       1   // Morse Puffer Überlauf

// ----------------------------------------------------------------------------
// MORSE TABELLEN:

// Morse Tabelle [0..79]:
// Morse Decoder und Encoder nutzen diese Tabelle, um Morse Code zu empfangen
// oder zu senden. Diese Tabelle enthält 16-Bit Konstanten. Jeder Tabellen-
// index [0..79] (oder jede Word Konstante) stellt ein Morse Zeichen dar.
// Die Punkte (dit) und Striche (dah) werden als 2 Bits gespeichert: Die Bits
// "01" stehen für ein dit und "11" für ein dah, gelesen von rechts nach links
// in der binären Darstellung. Zwischen dits und dahs eines Morse Zeichens
// muss man eine Pause mit der Länge eines dits senden. Zwischen Morse Zeichen
// gibt es eine Pause mit der Länge von drei dits (oder einem dah).
//
// Beispiel:                   Ende <<<<7<<6<<5<<4<<3<<2<<1<<<< Start
//                                  ---DahDitDitDahDitDitDit
// 0x35D5 = 0b0011010111010101 -> 0b 00 11 01 01 11 01 01 01 -> $ (Dollar)
flash word ms_ft[MORSESIGNS_MAXINDEX + 1] =
// Signale:
// Hex        Binär            Zeichen  Index  Signal
{0x5555, // 0b0101010101010101            0      HH
 0x0DD5, // 0b0000110111010101                   SK
 0x0377, // 0b0000001101110111                   CT
 0x3757, // 0b0011011101010111                   BK
 0x5D77, // 0b0101110101110111                   CL
 0xDF77, // 0b1101111101110111            5      CQ
 0x0FD7, // 0b0000111111010111                   DO
 0x5FD5, // 0b0101111111010101            7      SOS
//------------------------------------------------------
// Sonderzeichen:
// Hex        Binär            Zeichen  Index  Signal
 0x01DF, // 0b0000000111011111  ^G        8
 0x00FF, // 0b0000000011111111  CH,^H
 0x01FD, // 0b0000000111111101  ^J       10
 0x15D5, // 0b0001010111010101  /S
 0x01D5, // 0b0000000111010101  ^S               VE
 0x075F, // 0b0000011101011111  /Z
 0x035F, // 0b0000001101011111  .Z
 0x037D, // 0b0000001101111101  /A,°A    15
 0x00DD, // 0b0000000011011101  Ä                AA
 0x0177, // 0b0000000101110111  C~
 0x035D, // 0b0000001101011101  \E
 0x0175, // 0b0000000101110101  /E
 0x01F5, // 0b0000000111110101  Eth      20
 0x03DF, // 0b0000001111011111  ~N
 0x007F, // 0b0000000001111111  Ö
 0x00F5, // 0b0000000011110101  Ü
 0x017D, // 0b0000000101111101  Thorn
 0x17D5, // 0b0001011111010101  ß        25
//------------------------------------------------------
// Normale Zeichen:
// Hex        Binär            Zeichen  Index  Signal
 0x0F77, // 0b0000111101110111  !        26
 0x075D, // 0b0000011101011101  "
 0x35D5, // 0b0011010111010101  $
 0x015D, // 0b0000000101011101  &                AS
 0x07FD, // 0b0000011111111101  '        30
 0x01F7, // 0b0000000111110111  (                KN
 0x0DF7, // 0b0000110111110111  )
 0x01DD, // 0b0000000111011101  +                AR
 0x0F5F, // 0b0000111101011111  ,
 0x0D57, // 0b0000110101010111  -        35
 0x0DDD, // 0b0000110111011101  .
 0x01D7, // 0b0000000111010111  /                NR
 0x03FF, // 0b0000001111111111  0
 0x03FD, // 0b0000001111111101  1
 0x03F5, // 0b0000001111110101  2        40
 0x03D5, // 0b0000001111010101  3
 0x0355, // 0b0000001101010101  4
 0x0155, // 0b0000000101010101  5
 0x0157, // 0b0000000101010111  6
 0x015F, // 0b0000000101011111  7        45
 0x017F, // 0b0000000101111111  8
 0x01FF, // 0b0000000111111111  9
 0x057F, // 0b0000010101111111  :
 0x0777, // 0b0000011101110111  ;
 0x0357, // 0b0000001101010111  =        50      BT
 0x05F5, // 0b0000010111110101  ?                IMI
 0x077D, // 0b0000011101111101  @
 0x000D, // 0b0000000000001101  A
 0x0057, // 0b0000000001010111  B                DE
 0x0077, // 0b0000000001110111  C        55
 0x0017, // 0b0000000000010111  D
 0x0001, // 0b0000000000000001  E
 0x0075, // 0b0000000001110101  F
 0x001F, // 0b0000000000011111  G
 0x0055, // 0b0000000001010101  H        60
 0x0005, // 0b0000000000000101  I
 0x00FD, // 0b0000000011111101  J
 0x0037, // 0b0000000000110111  K                K
 0x005D, // 0b0000000001011101  L
 0x000F, // 0b0000000000001111  M        65
 0x0007, // 0b0000000000000111  N
 0x003F, // 0b0000000000111111  O
 0x007D, // 0b0000000001111101  P
 0x00DF, // 0b0000000011011111  Q
 0x001D, // 0b0000000000011101  R        70      R
 0x0015, // 0b0000000000010101  S
 0x0003, // 0b0000000000000011  T
 0x0035, // 0b0000000000110101  U
 0x00D5, // 0b0000000011010101  V
 0x003D, // 0b0000000000111101  W        75
 0x00D7, // 0b0000000011010111  X
 0x00F7, // 0b0000000011110111  Y
 0x005F, // 0b0000000001011111  Z
 0x0DF5};// 0b0000110111110101  _        79
// Bemerkungen: - SOS (Morse Zeichen ...---...) kann nicht in einer 16-Bit
//                Konstante gespeichert werden, weil SOS das einzige Morse
//                Zeichen mit 9 dits/dahs ist. Daher wird SOS als das (nicht
//                existierende) Morse Zeichen ...---.. (SOI) gespeichert und
//                muss in Decodern/Encodern besonders behandelt werden.


// Morse-ASCII-Tabelle [0..79]:
// Morse Decoder nutzen diese Tabelle, um Morse Code zu empfangen.
flash unsigned char ms_a0uc_ft[MORSESIGNS_MAXINDEX + 1] =
//H   S   C   B   C   C   D   S
{104,115, 99, 98, 99, 99,100,115,
//0                   5
//^   C   ^   %   ^   %   *   /A  Ä   C~  \E  /E  Et  ~N  Ö   Ü   To  ß
  94, 99, 94, 37, 94, 37, 42,193,196,199,200,201,208,209,214,220,222,223,
//        10                  15                  20                  25
//!  "  $  &  '  (  )  +  ,  -  .  /  0  1  2  3  4  5  6  7  8  9  :  ;
 33,34,36,38,39,40,41,43,44,45,46,47,48,49,50,51,52,53,54,55,56,57,58,59,
//           30             35             40             45
//=  ?  @  A  B  C  D   E   F   G   H   I   J   K   L   M   N   O   P   Q
 61,63,64,65,66,67, 68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, 81,
//50            55                  60                  65
//R   S   T   U   V   W   X   Y   Z   _
  82, 83, 84, 85, 86, 87, 88, 89, 90,95};       // Et = Eth,  To = Thorn
//70                  75             79

flash unsigned char ms_a1uc_ft[MORSESIGNS_MAXINDEX + 1] =
//H   K   T   K   L   Q   O   O
{104,107,116,107,108,113,111,111,
//0                   5
//G   H   J   S   S   Z   Z
 103,104,106,115,115,122,122, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//        10                  15                  20                  25
 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,
//           30             35             40             45
 32,32,32,32,32,32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//50            55                  60                  65
  32, 32, 32, 32, 32, 32, 32, 32, 32,32};       // Et = Eth,  To = Thorn
//70                  75             79

flash unsigned char ms_a2uc_ft[MORSESIGNS_MAXINDEX + 1] =
//                            S
{ 32, 32, 32, 32, 32, 32, 32,115,
//0                   5
  32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//        10                  15                  20                  25
 32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,32,
//           30             35             40             45
 32,32,32,32,32,32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32, 32,
//50            55                  60                  65
  32, 32, 32, 32, 32, 32, 32, 32, 32,32};       // Et = Eth,  To = Thorn
//70                  75             79
// Signale und Sonderzeichen sind in dieser Tabelle als Kleinbuchstaben
// gespeichert (hh, sk, ^g, ch ...).
// Bemerkungen: - Die Sonderzeichen  ^G, ^J, /S, ^S, /Z, .Z [Index 8, 10..14]
//                sind  hier  als    ^g, ^j, %s, ^s, %z, *z dargestellt.
//              - Wenn Morse Decoder eine Pause mit einer Länge von 7 dits
//                empfangen, müssen sie den ASCII Code ' ' (Leerzeichen [32])
//                ausgeben.


// ASCII-Morse-Tabelle [0..255]:
// Morse Encoder nutzen diese Tabelle, um Morse Code zu senden.
flash byte a_ms_ft[256] =
{51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//0              5             10             15             20
 51,51,51,51,51,51,51,51,
//24               30
//_  !  "  ?  $  ?  &  '  (  )  X  +  ,  -  .  /  0  1  2  3  4  5  6  7
 79,26,27,51,28,51,29,30,31,32,76,33,34,35,36,37,38,39,40,41,42,43,44,45,
//32      35             40             45             50             55
//8  9  :  ;  ?  =  ?  ?  @  A  B  C  D  E  F  G  H  I  J  K  L  M  N  O
 46,47,48,49,51,50,51,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,
//56         60             65             70             75
//P  Q  R  S  T  U  V  W  X  Y  Z  [  ?  ]  ?  _  ?  A  B  C  D  E  F  G
 68,69,70,71,72,73,74,75,76,77,78,31,51,32,51,79,51,53,54,55,56,57,58,59,
//80            85             90             95            100
//H  I  J  K  L  M  N  O  P  Q  R  S  T  U  V  W  X  Y  Z  {  ?  }  ?  ?
 60,61,62,63,64,65,66,67,68,69,70,71,72,73,74,75,76,77,78,31,51,32,51,51,
//104             110            115            120            125
//?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?
 51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//128 130            135            140            145            150
//?  ?  ?  ?  ?  ?  ?  ?  _  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?
 51,51,51,51,51,51,51,51,79,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,
//152    155            160            165            170            175
//?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ?  ? /A  ?  ?  Ä  ?  ? C~
 51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,51,15,51,51,16,51,51,17,
//176       180            185            190            195
//\E/E  ?  ?  ?  ?  ?  ? Et ~N  ?  ?  ?  ?  Ö  X  ?  ?  ?  ?  Ü  ? To  ß
 18,19,51,51,51,51,51,51,20,21,51,51,51,51,22,76,51,51,51,51,23,51,24,25,
//200          205            210            215            220
//? /A  ?  ?  Ä  ?  ? C~ \E /E  ?  ?  ?  ?  ?  ? Et ~N  ?  ?  ?  ?  Ö  /
 51,15,51,51,16,51,51,17,18,19,51,51,51,51,51,51,20,21,51,51,51,51,22,37,
//224             230            235            240            245
//?  ?  ?  ?  Ü  ? To  ?
 51,51,51,51,23,51,24,51};                      // Et = Eth,  To = Thorn
//248                255
// Bemerkungen: - ASCII Codes 91 '[' und 123 '{' werden umgewandelt in
//                Morse Code '(' [31].
//              - ASCII Codes 93 ']' und 125 '}' werden umgewandelt in
//                Morse Code ')' [32].
//              - ASCII Code 215 (Multiplikationszeichen) wird umgewandelt
//                in Morse Code 'X' [76].
//              - ASCII Code 247 (Divisionszeichen) wird umgewandelt in
//                Morse Code '/' [37].
//              - ASCII Codes 32 (sp) und 160 (nbsp) sind als '_' [79] in
//                dieser Tabelle dargestellt, müssen aber in Encodern
//                besonders behandelt werden: Ein Morse Encoder muss eine
//                Pause mit einer Länge von 7 dits für ein Leerzeichen
//                senden.
//              - Alle nicht druckbaren ASCII Codes [0..31] und andere
//                Codes, die nicht im Morse Code definiert sind, werden
//                in Morse Code '?' [51] umgewandelt.

// MORSE TABELLEN (ENDE)
// ----------------------------------------------------------------------------

/******************************************************************************/
// Variablen:
word timer;
byte morsedec_status;
byte morseenc_status;
byte morse_error;
#ifdef SOUND
word tonepitch;
#endif

// Feld Variablen für die Morse Tabellen:
word ms_rt[MORSESIGNS_MAXINDEX + 1];
unsigned char ms_a0uc_rt[MORSESIGNS_MAXINDEX + 1];
unsigned char ms_a1uc_rt[MORSESIGNS_MAXINDEX + 1];
unsigned char ms_a2uc_rt[MORSESIGNS_MAXINDEX + 1];
//byte a_ms_rt[256];

unsigned char morsedec_buffer[MORSEDEC_BUFFER_MAXINDEX + 2];
byte dec_write_pos, dec_read_pos;
unsigned char morseenc_buffer[MORSEENC_BUFFER_MAXINDEX + 2];
byte enc_write_pos, enc_read_pos;

word decspeed;
byte speedvar;

word encspeed;

#ifdef DEBUG
word ditlength, dahlength;
#endif

/******************************************************************************/
// Funktionen:

/**
 * Kopiere die Morse Tabellen vom Flash Speicher ins RAM
 *
 */
void copyFlashTables2RAM(void)
{
    ms_rt = ms_ft;
    ms_a0uc_rt = ms_a0uc_ft;
    ms_a1uc_rt = ms_a1uc_ft;
    ms_a2uc_rt = ms_a2uc_ft;
//    a_ms_rt = a_ms_ft;
}

/**
 * Wandele Kleinbuchstaben in Großbuchstaben um
 *
 * Eingabe: ASCII Code [0..255]
 * Ausgabe: ASCII Code, nur mit Großbuchstaben
 *
 */
unsigned char Lower2UpperCase(unsigned char ch)
{unsigned char chuc;
    chuc = ch;
    if ((ch >= 97) && (ch <= 122)) {
        chuc = chuc - 32;
    }
    if ((ch >= 224) && (ch <= 254) && (ch != 247)) {
        chuc = chuc - 32;
    }
    return (chuc);
}

/**
 * Wandele Großbuchstaben in Kleinbuchstaben um
 *
 * Eingabe: ASCII Code [0..255]
 * Ausgabe: ASCII Code, nur mit Kleinbuchstaben
 *
 */
unsigned char Upper2LowerCase(unsigned char ch)
{unsigned char chlc;
    chlc = ch;
    if ((ch >= 65) && (ch <= 90)) {
        chlc = chlc + 32;
    }
    if ((ch >= 192) && (ch <= 222) && (ch != 215)) {
        chlc = chlc + 32;
    }
    return (chlc);
}

/**
 * Ausgabe des Morse Codes eines Morse Tabellenindex
 *
 * Eingabe: Morse Tabellenindex [0..MORSESIGNS_MAXINDEX]
 * Ausgabe: Morse Code (Siehe Tabelle ms_ft[] oben!)
 *
 */
word MsIndex2MorseCode(byte msindex)
{
    morse_error = false;
    return (ms_rt[msindex]);
}

/**
 * Ausgabe des Tabellenindex eines Morse Codes
 *
 * Eingabe: Morse Code (Siehe Tabelle ms_ft[] oben!)
 * Ausgabe: Morse Tabellenindex [0..MORSESIGNS_MAXINDEX]
 *
 */
byte MorseCode2MsIndex(word morsecode)
{byte msidx;
    for (msidx = 0; msidx <= MORSESIGNS_MAXINDEX; msidx++) {
        if (morsecode == ms_rt[msidx]) {break;}
    }
    if (msidx <= MORSESIGNS_MAXINDEX) {
        morse_error = false;
        return (msidx);                 // Morse Tabellenindex
    }
    else {
        morse_error = true;             // Unbekannter Morse Code:
        return (51);                    //  Gib Tabellenindex von '?' zurück
    }
}

/**
 * Ausgabe des Morse Zeichen Namens eines Morse Codes
 *
 * Eingabe: Morse Code (Siehe Tabelle ms_ft[] oben!)
 * Ausgabe: String mit dem Morse Zeichen Namen (1..3 ASCII Zeichen)
 *
 */
void MorseCode2MsName(unsigned char msname[], word morsecode)
{byte msidx;
    msidx = MorseCode2MsIndex(morsecode);
    msname[0] = ms_a0uc_rt[msidx];
    msname[1] = ms_a1uc_rt[msidx];
    if (msname[1] == 32) {msname[1] = 0;}
    msname[2] = ms_a2uc_rt[msidx];
    if (msname[2] == 32) {
        msname[2] = 0;
    }
    else {
        msname[3] = 0;
    }
}

/**
 * Ausgabe des Morse Tabellenindex eines Morse Zeichen Namens
 *
 * Eingabe: String mit dem Morse Zeichen Namen (1..3 ASCII Zeichen)
 * Ausgabe: Morse Tabellenindex [0..MORSESIGNS_MAXINDEX]
 *
 */
byte MsName2MsIndex(unsigned char msname[])
{byte msidx;
    for (msidx = 0; msidx <= MORSESIGNS_MAXINDEX; msidx++) {
        if (msname[0] == ms_a0uc_rt[msidx]) {
            if ((ms_a1uc_rt[msidx] == 32)
             || (msname[1] == ms_a1uc_rt[msidx])) {
                if ((ms_a2uc_rt[msidx] == 32)
                 || (msname[2] == ms_a2uc_rt[msidx])) {
                    break;
                }
            }
        }
    }
    if (msidx <= MORSESIGNS_MAXINDEX) {
        morse_error = false;
        return (msidx);                 // Morse Tabellenindex
    }
    else {
        morse_error = true;             // Unbekannter Morse Zeichen Name:
        return (51);                    //  Gib Tabellenindex von '?' zurück
    }
}

/**
 * Ausgabe des Morse Zeichens eines Morse Codes
 *
 * Eingabe: Morse Code (Siehe Tabelle ms_ft[] oben!)
 * Ausgabe: String mit dem Morse Zeichen (1..9 dits [.] oder dahs [-])
 *
 * Beispiel: $  -> 0b0011010111010101  -> Morse Zeichen ...-..-
 *
 */
void MorseCode2MorseSign(unsigned char morsesign[], word morsecode)
{byte i; word ms_code;
    ms_code = morsecode;
    i = 0;
    do {
        switch (ms_code & 3) {
            case 1 :                    // dit!
                morsesign[i] = '.';
                i++; break;
            case 3 :                    // dah!
                morsesign[i] = '-';
                i++;
        }
        ms_code = ms_code >> 2;
    } while (ms_code);
    if (morsecode == 0x5FD5) {          // SOS: Füge letztes dit hinzu!
        morsesign[i] = '.';
        i++;
    }
    morsesign[i] = 0;
    morse_error = false;
}

/**
 * Ausgabe des Morse Codes eines Morse Zeichens
 *
 * Eingabe: String mit dem Morse Zeichen (1..9 dits [.] oder dahs [-])
 * Ausgabe: Morse Code (Siehe Tabelle ms_ft[] oben!)
 *
 * Beispiel: $  -> Morse Zeichen ...-..-  -> 0b0011010111010101
 *
 */
word MorseSign2MorseCode(unsigned char morsesign[])
{byte i; unsigned char ch; word ms_code;
    ms_code = 0;
    ch = 1;
    for (i = 0; i <= 7; i++) {
        ms_code = ms_code >> 2;
        if (ch) {
            ch = morsesign[i];
            switch (ch) {
                case '.' :              // dit!
                    ms_code = ms_code | 0x4000; break;
                case '-' :              // dah!
                    ms_code = ms_code | 0xC000;
            }
        }

    }
    if ((ms_code == 0x5FD5) && (morsesign[8] != '.')) {
        ms_code = 0x05F5;    // SOS: Wenn das letzte dit nicht existiert,
        morse_error = true;  //      gib '?' zurück!
    }
    else {
        morse_error = false;
    }
    return (ms_code);
}

/******************************************************************************/
// Morse Decoder Funktionen:

/**
 * Lösche den Morse Decoder Ring Puffer
 *
 */
void clearMorseDecBuffer(void)
{
    morsedec_status = MORSE_BUFFER_OK;  // Decoder Puffer Status ok
    dec_write_pos = 255;                // Puffer Schreibposition zurücksetzen
    dec_read_pos = 255;                 // Puffer Leseposition zurücksetzen
}

/**
 * Initialisiere den Morse Decoder
 *
 * Einmal aufrufen, bevor die Morse Decoder (Empfänger) Funktion benutzt wird!
 *
 */
void initMorseDecoder(void)
{
    copyFlashTables2RAM();              // Fülle die Tabellen im RAM
    Port_DataDirBit(MORSEDEC_IN, PORT_IN); // Decoder Eingangs Pin
    Port_WriteBit(MORSEDEC_IN, 1);         // MORSEDEC_IN -> Pullup
    morse_error = false;                // Setze das Morse Fehler Flag zurück
    clearMorseDecBuffer();              // Lösche den Decoder Puffer
    decspeed = SPEED;                   // Decoder Speed
    speedvar = SPEED_VAR;               // Decoder Speed Variation
#ifdef SOUND
    tonepitch = Tone_C2;                // Tonhöhe festlegen
#endif
}

/**
 * Speichere ein decodiertes Signal / Morse Zeichen in den Decoder Ring Puffer
 *
 * Eingabe: ASCII Zeichen (Teil eines Strings mit dem Signal / Zeichen Namen)
 *
 */
void storeMsChar2DecBuffer(unsigned char ch)
{
    if (getMorseDecBufferLength() < MORSEDEC_BUFFER_MAXINDEX) {
        dec_write_pos++;
        if (dec_write_pos > MORSEDEC_BUFFER_MAXINDEX) {
            dec_write_pos = 0;
        }
        morsedec_buffer[dec_write_pos] = ch;
        morsedec_status = MORSE_BUFFER_OK;      // Decoder Puffer Status ok
    }
    else {
        morsedec_status = MORSE_BUFFER_OVERFLOW;// Decoder Puffer Überlauf
    }
}

/**
 * Morse Decoder
 *
 * Die Funktion decodeMorse() muss alle 1ms aufgerufen werden.
 *
 */
void decodeMorse(void)
{static unsigned char ms_sign[10]; byte temp;
 static word signal, pause;
 static byte ditdah, ditdah_cnt;
 unsigned char ms_name[4];
#ifdef SOUND
 static byte tone_off;
#endif
#ifdef LIMITED_PAUSE
 static byte space_cnt;
#endif
    Thread_Lock(1);
    temp = Port_ReadBit(MORSEDEC_IN);   // Lese den Morse Pegel
    if (temp) {                         // Highpegel (Morsesignal an = dit/dah)
#ifdef SOUND
        if (tone_off) {
            sound(tonepitch);
            tone_off = false;
        }
#endif
#ifdef LIGHT
        Port_WriteBit(PORT_LED1, 1);
#endif
        signal++;
        if (pause > (decspeed * 2)) {   // Pause > 2 dits:
            if (ditdah) {               //  Morse Zeichen Ende (Länge 3 dits)
                ms_sign[ditdah_cnt] = ditdah;
                ditdah_cnt++;
                ms_sign[ditdah_cnt] = 0;
                ditdah_cnt = 0;
                ditdah = 0;
                MorseCode2MsName(ms_name, MorseSign2MorseCode(ms_sign));
                temp = 0;
                while (ms_name[temp]) {
                    storeMsChar2DecBuffer(ms_name[temp++]);
                }
            }
            pause = 0;
        }
        if (pause) {                    // Kurze Pause:
            if (ditdah) {               //  Dit oder dah Ende (Länge 1 dit)
                ms_sign[ditdah_cnt] = ditdah;
                ditdah_cnt++;
                ms_sign[ditdah_cnt] = 0;
                if (ditdah_cnt > 8) {ditdah_cnt = 0;}
                ditdah = 0;
            }
            pause = 0;
        }
    }
    else {                              // Lowpegel (Morsesignal aus = Pause)
#ifdef SOUND
        sound_off();
        tone_off = true;
#endif
#ifdef LIGHT
        Port_WriteBit(PORT_LED1, 0);
#endif
        pause++;
        if (pause > (decspeed * 5)) {   // Pause > 5 dits:
            if (ditdah) {               //  Leerzeichen oder längere Pause
                ms_sign[ditdah_cnt] = ditdah;
                ditdah_cnt++;
                ms_sign[ditdah_cnt] = 0;
                ditdah_cnt = 0;
                ditdah = 0;
                MorseCode2MsName(ms_name, MorseSign2MorseCode(ms_sign));
                temp = 0;
                while (ms_name[temp]) {
                    storeMsChar2DecBuffer(ms_name[temp++]);
                }
#ifdef LIMITED_PAUSE
                space_cnt = SPACE_CNT_LIMIT;
                space_cnt--;
#endif
                storeMsChar2DecBuffer(' ');     // Füge ein Leerzeichen nach
                pause = 0;                      //  dem Zeichen an
            }
#ifdef LIMITED_PAUSE
            if (space_cnt) {
#endif
                if (pause >= (decspeed * 7)) {  // Pause >= 7 dits:
                    storeMsChar2DecBuffer(' '); //  Füge Leerzeichen an
                    pause = pause - (decspeed * 7);
#ifdef LIMITED_PAUSE
                    space_cnt--;
#endif
                }
#ifdef LIMITED_PAUSE
            }
            else {
                pause = 0;
            }
#endif
        }
        if (signal > (decspeed * 2)) {          // Highpegel > 2 dits:
#ifdef DEBUG
            dahlength = signal;
#endif
            ditdah = '-';                       //  Dah (Länge 3 dits)!
            if (signal >= (decspeed * 3.3)) {   // Highpegel >= 3,3 dits (+10%):
                decspeed = decspeed + speedvar; //  Reduziere Decoder Speed
                if (decspeed > SPEED_MIN) {decspeed = SPEED_MIN;}
            }
            signal = 0;
        }
        if (signal) {                           // Kurzer Highpegel:
#ifdef DEBUG
            ditlength = signal;
#endif
            ditdah = '.';                       //  Dit!
            if (signal <= (decspeed * 0.9)) {   // Highpegel <= 0,9 dits (-10%):
                decspeed = decspeed - speedvar; //  Erhöhe Decoder Speed
                if (decspeed < SPEED_MAX) {decspeed = SPEED_MAX;}
            }
            signal = 0;
        }
    }
    Thread_Lock(0);
}

/**
 * Lese nächstes Zeichen aus dem Morse Decoder Ring Puffer
 *
 * Ausgabe: Druckbares ASCII Zeichen [32..255] (als Teil eines
 *          empfangenen/decodierten Signal / Morse Zeichen Namens)
 *          ODER 0 (false), wenn der Ring Puffer leer ist
 *
 */
unsigned char readMorseChar(void)
{unsigned char ch;
    if (dec_read_pos != dec_write_pos) {
        dec_read_pos++;
        if (dec_read_pos > MORSEDEC_BUFFER_MAXINDEX) {
            dec_read_pos = 0;
        }
        ch = morsedec_buffer[dec_read_pos];
    }
    else {
        ch = 0;
    }
    return (ch);
}

/**
 * Lese nächste [numberOfChars] Zeichen aus dem Morse Decoder Ring Puffer
 *
 * Ausgabe: Anzahl der Zeichen, die nach *buf kopiert wurden,
 *          String *buf mit den kopierten Zeichen
 *
 */
byte readMorseChars(unsigned char buf[], byte numberOfChars)
{byte i; unsigned char ch;
    i = 0;
    while (i < numberOfChars) {
        ch = readMorseChar();
        if (ch) {
            buf[i] = ch;
        }
        else {break;}
        i++;
    }
    buf[i] = 0;
    return (i);
}

/**
 * Ermittele die Anzahl der Zeichen im Morse Decoder Ring Puffer
 *
 * Ausgabe: Anzahl der Zeichen (0: Puffer ist leer!)
 *
 */
byte getMorseDecBufferLength(void)
{int dec_posdiff;
    dec_posdiff = dec_write_pos - dec_read_pos;
    if (dec_posdiff < 0) {
        dec_posdiff = dec_posdiff + (MORSEDEC_BUFFER_MAXINDEX + 1);
    }
    return (dec_posdiff);
}

/******************************************************************************/
// Morse Encoder Funktionen:

/**
 * Inititialisiere den Morse Encoder
 *
 * Einmal aufrufen, bevor die Morse Encoder (Sender) Funktion benutzt wird!
 *
 */
void initMorseEncoder(void)
{
    copyFlashTables2RAM();              // Fülle die Tabellen im RAM
	Port_DataDirBit(MORSEENC_IN, PORT_OUT); // Encoder Ausgangs Pin
    Port_WriteBit(MORSEENC_IN, 0);          // Ausgang low
    morse_error = false;                // Setze das Morse Fehler Flag zurück
    morseenc_status = MORSE_BUFFER_OK;  // Encoder Puffer Status ok
    enc_write_pos = 255;                // Puffer Schreibposition zurücksetzen
    enc_read_pos = 255;                 // Puffer Leseposition zurücksetzen
    encspeed = SPEED;                   // Setze Encoder Speed
#ifdef SOUND
    tonepitch = Tone_C2;                // Tonhöhe festlegen
#endif
}

/**
 * Hole den nächsten Morse Tabellenindex aus dem Morse Encoder Ring Puffer
 *
 * Ausgabe: Morse Tabellenindex [0..MORSESIGNS_MAXINDEX(..127)]
 *          ODER Pausenlänge [129..255] (Pause 1..127 dits)
 *          ODER 128 (0x80), wenn der Ring Puffer leer ist
 *
 */
byte fetchMsIndexFromEncBuffer(void)
{byte msidx;
    if (enc_read_pos != enc_write_pos) {
        enc_read_pos++;
        if (enc_read_pos > MORSEENC_BUFFER_MAXINDEX) {
            enc_read_pos = 0;
        }
        msidx = morseenc_buffer[enc_read_pos];
    }
    else {
        msidx = 0x80;
    }
    return (msidx);
}

/**
 * Morse Encoder
 *
 * Die Funktion encodeMorse() muss alle 1ms aufgerufen werden.
 *
 */
void encodeMorse(void)
{static byte busy_flag, signal_flag, pause_flag, sos_flag, pause_dits;
 static word timer, ms_code; byte msidx;
    Thread_Lock(1);
    timer++;
    if (busy_flag) {                        // Encoder beschäftigt!
        if (signal_flag) {                  // Highpegel (dit/dah) senden
            if (!pause_flag) {              // Warten auf Highpegel Ende
                if (timer >= (encspeed * (ms_code & 3))) {
#ifdef SOUND
                    sound_off();
#endif
#ifdef LIGHT
                    Port_WriteBit(PORT_LED1, 0);
#endif
                    Port_WriteBit(MORSEENC_IN, 0);
                    timer = 0;
                    pause_flag = true;
                    ms_code = ms_code >> 2;
                }
            }
            else {                          // Pause nach Highpegel
                if (ms_code) {              // Dit/dah (Highpegel) Ende:
                    if (timer >= encspeed) {
                        signal_flag = false;//  Pause 1 dit
                    }
                }
                else {                      // Morse Zeichen Ende:
                    if (sos_flag) {         //  Falls SOS:
                        ms_code = 0x0001;   //   Füge letztes dit an
                        sos_flag = false;
                    }
                    else {                  //  Falls Zeichen Ende:
                        if (timer >= (encspeed * 3)) {
                            busy_flag = false;// Pause 3 dits
                        }
                    }
                }
            }
        }
        else {                              // Highpegel (dit/dah) Ende
            if (pause_dits) {               // Mache eine längere Pause
                if (timer >= (encspeed * pause_dits)) {
                    busy_flag = false;      // Längere Pause Ende
                }
            }
            else {                          // Starte neuen Highpegel (dit/dah)
#ifdef SOUND
                sound(tonepitch);
#endif
#ifdef LIGHT
                Port_WriteBit(PORT_LED1, 1);
#endif
                Port_WriteBit(MORSEENC_IN, 1);
                timer = 0;
                pause_flag = false;
                signal_flag = true;
            }
        }
    }
    else {                                  // Encoder nicht beschäftigt!
        msidx = fetchMsIndexFromEncBuffer();// Hole nächsten Index zum Senden
        if (msidx == 0x80) {                //  aus dem Ring Puffer
            Thread_Lock(0);
            return;                         // Puffer ist leer: Return
        }
        else {
            if (msidx < 0x80) {             // Zu sendendes Morse Zeichen
                ms_code = MsIndex2MorseCode(msidx);
                if (ms_code == 0x5FD5) {
                    sos_flag = true;        // Zeichen ist SOS
                }
                else {
                    sos_flag = false;
                }
                pause_dits = 0;
            }
            else {                          // (msidx > 0x80): Längere Pause
                timer = 0;
                pause_dits = msidx - 0x80;
            }
            signal_flag = false;
            busy_flag = true;               // Zeichen / längere Pause kann
        }                                   //  gesendet werden
    }
    Thread_Lock(0);
}

/**
 * Speichere einen Morse Tabellenindex in den Morse Encoder Ring Puffer
 *
 * Eingabe: Morse Tabellenindex [0..MORSESIGNS_MAXINDEX(..127)]
 *          ODER Pausenlänge [129..255] (Pause 1..127 dits)
 *
 */
void storeMsIndex2EncBuffer(byte msindex)
{
    if (getMorseEncBufferLength() < MORSEENC_BUFFER_MAXINDEX) {
        enc_write_pos++;
        if (enc_write_pos > MORSEENC_BUFFER_MAXINDEX) {
            enc_write_pos = 0;
        }
        morseenc_buffer[enc_write_pos] = msindex;
        morseenc_status = MORSE_BUFFER_OK;       // Encoder Puffer Status ok
    }
    else {
        morseenc_status = MORSE_BUFFER_OVERFLOW; // Encoder Puffer Überlauf
    }
}

/**
 * Schreibe eine zu sendende Pausenlänge in den Morse Encoder Ring Puffer
 *
 * Eingabe: Pausenlänge [1..127 dits] (0,14..18,14 Leerzeichen)
 *
 * Mit dieser Funktion kann man längere Pausen erreichen.
 *   Beispiele:
 *   pauseMorse(7);  ist identisch mit  writeMorseChar(' ');
 *   pauseMorse(14); ist identisch mit  writeMorseString("  ");
 * Die Funktion pauseMorse(len) schreibt nur ein Byte in den Encoder Ring
 * Puffer für eine längere Pause, während writeMorseChar(' ') ein Byte für
 * jedes zu sendende Leerzeichen schreibt. Man sollte writeMorseChar(' ')
 * benutzen, um einzelne Leerzeichen (zwischen Worten) und pauseMorse(len),
 * um längere Pausen zu senden.
 *
 * ACHTUNG: !-------------------------------------------------------------!
 *          ! Die max. Pausenlänge, die man mit dieser Funktion erreichen !
 *          ! kann, beträgt etwa 6 Sekunden!  Damit hängt der Eingabewert !
 *          ! dieser Funktion von encspeed ab!!!                          !
 *          !-------------------------------------------------------------!
 *          !     ==>  Max. Pausenlänge [dits] = 6000 / encspeed  <==     !
 *          !-------------------------------------------------------------!
 *           Für encspeed Werte von 8 (SPEED_MAX) bis 47 beträgt die max.
 *           Pausenlänge 127 dits.  Für encspeed Werte von 48 bis 400
 *           (SPEED_MIN) kann man die max. Anzahl von dits mit der obigen
 *           Formel berechnen.
 *           Bei SPEED_MIN kann man nur für 15 (6000 / 400) dits pausieren!
 *
 */
void pauseMorse(byte len)
{
	if (len) {
		storeMsIndex2EncBuffer(len | 0x80);
	}
}

/**
 * Schreibe ein zu sendendes Zeichen in den Morse Encoder Ring Puffer
 *
 * Eingabe: ASCII Code [0..255]
 *
 */
void writeMorseChar(unsigned char ch)
{static byte sign_flag, chidx; byte msidx;
 static unsigned char last_3ch[4];
    Thread_Lock(1);
	switch (ch) {
		case 32 :						// Leerzeichen   [ASCII Code 32]
		case 160 :						// Geschütztes Leerz. [ASCII Code 160]
			if (sign_flag) {			// Leerzeichen direkt nach einem
				pauseMorse(4);			//  Zeichen (Länge 4 dits)
				if (morseenc_status == MORSE_BUFFER_OK) {
					sign_flag = false;
				}
			}
			else {						// Pause für alle anderen Leerzeichen
				pauseMorse(7);			//  (Länge 7 dits)
			}
			break;
		default :
			last_3ch[chidx] = ch; last_3ch[chidx + 1] = 0;
			msidx = MsName2MsIndex(last_3ch);// Name in der Morse Tabelle?
			if (morse_error) {
				chidx++;
				if (chidx > 2) {chidx = 0;}
                Thread_Lock(0);
    			return;
			}
			storeMsIndex2EncBuffer(msidx);
			if (morseenc_status == MORSE_BUFFER_OK) {
				sign_flag = true;
			}
	}
	chidx = 0;
    Thread_Lock(0);
}

/**
 * Schreibe einen zu sendenden String in den Morse Encoder Ring Puffer
 *
 * Eingabe: String mit ASCII Text
 *
 */
void writeMorseString(unsigned char str[])
{byte pos;
    pos = 0;
	while (str[pos]) {
		writeMorseChar(str[pos]);
        pos++;
	}
}

/**
 * Ermittele die Anzahl der Indices im Morse Encoder Ring Puffer
 *
 * Ausgabe: Anzahl der Indices (0: Puffer ist leer!)
 *
 */
byte getMorseEncBufferLength(void)
{int enc_posdiff;
	enc_posdiff = enc_write_pos - enc_read_pos;
	if (enc_posdiff < 0) {
		enc_posdiff = enc_posdiff + (MORSEENC_BUFFER_MAXINDEX + 1);
	}
	return (enc_posdiff);
}

/******************************************************************************/
// Nützliche LCD Funktionen:

#ifndef DEBUG
/**
 * Zeige empfangene Morse Zeichen auf dem LCD 16x2 Zeichen als ASCII Text
 *
 */
void writeMorseLCD(void)
{static byte pos; static unsigned char line2[17]; unsigned char ch;
	ch = readMorseChar();
	if (ch) {
    	writeCharLCD(ch);
		line2[pos] = ch;
		pos++;
		if (pos >= 16) {
			pos = 0;
			clearLCD();
			writeStringLCD(line2);		// Kopiere Zeile 2 nach Zeile 1
			setCursorPosLCD(1, 0);		// Zeile 2, Position 1
		}
	}
}

#else

/**
 * Zeige Decoder Debug Informationen auf dem LCD
 *
 * Format: .0000 -0000 S000
 *         B000 A[XXX] D000
 *
 *   .    -> Dit Länge [0.1ms]
 *   -    -> Dah Länge [0.1ms]
 *   S    -> Decoder Speed (sollte (dit Länge / 10) sein!) [ms]
 *   B    -> Decoder Pufferlänge (Zeichen noch im Puffer)
 *   A    -> Die 3 zuletzt empfangenen ASCII Zeichen
 *   D    -> Abweichung (Decoder Speed - (dit Länge / 10)) [ms]
 *
 */
void showDebugInfoLCD(void)
{static unsigned char last_3ch[4]; unsigned char ch;
	ch = readMorseChar();
	if (ch) {
		last_3ch[0] = last_3ch[1]; last_3ch[1] = last_3ch[2];
		last_3ch[2] = ch; last_3ch[3] = 0;
		setCursorPosLCD(0, 0);			// Zeile 1, Position 1
		printLCD(".");
		printIntegerLCD(ditlength);
		printLCD(" -");
		printIntegerLCD(dahlength);
		printLCD(" S");
		printIntegerLCD(decspeed);
		printLCD("   ");
		setCursorPosLCD(1, 0);			// Zeile 2, Position 1
		printLCD("B");
		printIntegerLCD(getMorseDecBufferLength());
		printLCD(" A[");
    	writeCharLCD(last_3ch[0]);
    	writeCharLCD(last_3ch[1]);
    	writeCharLCD(last_3ch[2]);
		printLCD("] D");
		printIntegerLCD(decspeed - ditlength);
		printLCD("   ");
	}
}
#endif

#endif

/******************************************************************************
 * Info
 * ****************************************************************************
 * Changelog:
 * - v. 1.3w 2012 by Dirk
 *
 * ****************************************************************************
 */

/*****************************************************************************/
// EOF

Demos

RP6 Base

...

RP6 CONTROL M32

...

RP6 CCPRO M128

...


Optionen

Direkteingabe von Morse-Code

Rundfunkempfang von Morse-Code

Morse-Funkstrecke

Weiteres

Erfahrungsberichte, Weiterentwicklung

... kann gerne ergänzt werden ...


Siehe auch


Weblinks


Autoren

--Dirk 20:21, 12. Mär 2012 (CET)


LiFePO4 Speicher Test